Nissan Maxima. Manual — part 340
KEY CYLINDER SWITCH
DLK-79
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Special Repair Requirement
INFOID:0000000009471656
1.
PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
DLK-12, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
DLK-80
< DTC/CIRCUIT DIAGNOSIS >
UNLOCK SENSOR
UNLOCK SENSOR
Description
INFOID:0000000009471657
Detects door lock condition of driver door.
Component Function Check
INFOID:0000000009471658
1.
CHECK FUNCTION
With CONSULT
Check unlock sensor UNLK SEN
−DR in “Data Monitor” mode.
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009471659
Regarding Wiring Diagram information, refer to
.
1.
CHECK UNLOCK SENSOR POWER SUPPLY
Check signal between BCM connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> GO TO 2
Monitor item
Condition
UNLK SEN
−DR
Front door lock (driver side) LOCK : ON
Front door lock (driver side) UNLOCK : OFF
ALKIA0352ZZ
Terminals
Front door lock assembly
LH condition
Voltage (V)
(Approx.)
(+)
(–)
BCM connector
Terminal
M18
27
Ground
Locked
Unlocked
0
JPMIA0011GB
UNLOCK SENSOR
DLK-81
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
CHECK UNLOCK SENSOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and front door lock assembly LH connector.
3. Check continuity between BCM connector and front door lock assembly LH connector.
4. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness between BCM and front door lock assembly LH.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly LH connector and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK BCM OUTPUT SIGNAL
1. Connect BCM harness connector.
2. Check signal between BCM connector and ground with oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace BCM. Refer to
BCS-79, "Removal and Installation"
5.
CHECK UNLOCK SENSOR
DLK-82, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Replace front door lock assembly LH. Refer to
DLK-221, "FRONT DOOR LOCK : Removal and
6.
CHECK INTERMITTENT INCIDENT
BCM connector
Terminal
Front door lock assem-
bly LH connector
Terminal
Continuity
M18
27
D10
3
Yes
BCM connector
Terminal
Ground
Continuity
M18
27
No
Front door lock assembly
LH connector
Terminal
Ground
Continuity
D10
4
Yes
Terminals
Voltage (V)
(Approx.)
(+)
(–)
BCM connector
Terminal
M18
27
Ground
ALKIA0354ZZ
JPMIA0011GB
DLK-82
< DTC/CIRCUIT DIAGNOSIS >
UNLOCK SENSOR
GI-41, "Intermittent Incident"
>> Inspection End.
Component Inspection
INFOID:0000000009471660
1.
CHECK UNLOCK SENSOR
Check unlock sensor.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace front lock assembly LH. Refer to
DLK-221, "FRONT DOOR LOCK : Removal and Instal-
.
Terminal
Front door lock assembly LH
condition
Continuity
Front door lock assembly LH
3
4
Unlock
Yes
Lock
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст