Nissan Maxima. Manual — part 952
PREPARATION
PWC-105
< PREPARATION >
[LH&RH FRONT WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009467716
The actual shapes of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
PWC-106
< PERIODIC MAINTENANCE >
[LH&RH FRONT WINDOW ANTI-PINCH]
PRE-INSPECTION FOR DIAGNOSTIC
PERIODIC MAINTENANCE
PRE-INSPECTION FOR DIAGNOSTIC
Basic Inspection
INFOID:0000000009467717
BASIC INSPECTION
1.
INSPECTION START
1. Check the service history.
2. Check the following parts.
• Fuse/circuit breaker blown.
• Poor connection, open or short circuit of harness connector.
• Battery voltage.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace the malfunctioning parts.
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
PWC-107
< REMOVAL AND INSTALLATION >
[LH&RH FRONT WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
REMOVAL AND INSTALLATION
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Removal and Installation
INFOID:0000000009467718
REMOVAL
1. Remove the front door grip cover. Refer to
DLK-214, "FRONT DOOR : Removal and Installation"
2. Remove the clip (A) from the door grip using a suitable tool.
3. Release the metal clip and lift the main power window and door
lock/unlock switch (2) and finisher (1) as an assembly starting
from the rear using a suitable tool, pull upward to remove it from
the front door finisher.
: Metal clip
4. Disconnect the harness connector from the main power window
and door lock/unlock switch.
5. Release the pawls on each side to separate the switch finisher
(1) from the main power window and door lock/unlock switch (2).
: Pawl
CAUTION:
Do not damage the pawl of the switch finisher.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Whenever the main power window and door lock/unlock switch is disconnected from the harness connector, it
is necessary to perform the Initialization procedure. Refer to
PWC-7, "ADDITIONAL SERVICE WHEN
REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement"
.
ALKIA1666ZZ
ALKIA1667ZZ
PWC-108
< REMOVAL AND INSTALLATION >
[LH&RH FRONT WINDOW ANTI-PINCH]
POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
Removal and Installation
INFOID:0000000009467719
REMOVAL
1. Remove the front door grip cover. Refer to
INT-18, "Removal and Installation"
.
2. Remove the clip (A) from the door grip using suitable tool.
3. Release the metal clip and lift the power window and door lock/
unlock switch (2) and switch finisher (1) as an assembly starting
from the rear using a suitable tool, pull upward to remove it from
the front door finisher.
: Metal clip
4. Disconnect the harness connector from the power window and
door lock/unlock switch.
5. Release the pawls on each side to separate the switch finisher
(1) from the power window and door lock/unlock switch (2).
: Pawl
CAUTION:
Do not damage the pawl of the switch finisher.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Whenever the power window and door lock/unlock switch is disconnected from the harness connector, it is
necessary to perform the Initialization procedure. Refer to
PWC-7, "ADDITIONAL SERVICE WHEN REMOV-
ING BATTERY NEGATIVE TERMINAL : Special Repair Requirement"
ALKIA1668ZZ
ALKIA1669ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст