Nissan Maxima. Manual — part 815
LAN-72
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 2)]
MAIN LINE BETWEEN DLC AND HVAC CIRCUIT
DTC/CIRCUIT DIAGNOSIS
MAIN LINE BETWEEN DLC AND HVAC CIRCUIT
Diagnosis Procedure
INFOID:0000000009990306
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect the following harness connectors.
-
ECM
-
A/C auto amp.
4. Check the continuity between the data link connector and the A/C auto amp. harness connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the data link connector and the A/C auto
amp.
NO
>> Repair the main line between the data link connector and the A/C auto amp.
Data link connector
A/C auto amp. harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M22
6
M37
1
Existed
14
2
Existed
LAN
MAIN LINE BETWEEN HVAC AND A-BAG CIRCUIT
LAN-73
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 2)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MAIN LINE BETWEEN HVAC AND A-BAG CIRCUIT
Diagnosis Procedure
INFOID:0000000009990307
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect the following harness connectors.
-
A/C auto amp.
-
Harness connectors M1 and E30
4. Check the continuity between the A/C auto amp. harness connector and the harness connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the A/C auto amp. and the air bag diagnosis
sensor unit.
NO
>> Repair the main line between the A/C auto amp. and the air bag diagnosis sensor unit.
A/C auto amp. harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M37
1
M1
15G
Existed
2
8G
Existed
LAN-74
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 2)]
MAIN LINE BETWEEN A-BAG AND ABS CIRCUIT
MAIN LINE BETWEEN A-BAG AND ABS CIRCUIT
Diagnosis Procedure
INFOID:0000000009990308
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector M1
-
Harness connector E30
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the following harness connectors.
-
A/C auto amp.
-
Harness connectors M1 and E30
2. Check the continuity between the A/C auto amp. harness connector and the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the air bag diagnosis sensor unit and the harness connector M1.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the connector of ABS actuator and electric unit (control unit).
2. Check the continuity between the harness connector and the ABS actuator and electric unit (control unit)
harness connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the air bag diagnosis sensor unit and the
ABS actuator and electric unit (control unit).
NO
>> Repair the main line between the harness connector E30 and the ABS actuator and electric unit
(control unit).
A/C auto amp. harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M37
1
M1
15G
Existed
2
8G
Existed
Harness connector
ABS actuator and electric unit (control unit)
harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E30
15G
E26
26
Existed
8G
15
Existed
LAN
ECM BRANCH LINE CIRCUIT
LAN-75
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 2)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ECM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000009990309
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
Models without automatic drive positioner
•
ECM
•
Harness connector E30
•
Harness connector M1
-
Models with automatic drive positioner
•
ECM
•
Harness connector E29
•
Harness connector B10
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of ECM.
2. Check the resistance between the ECM harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the ECM branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the ECM. Refer to
Is the inspection result normal?
YES (Present error)>>Replace the ECM. Refer to
EC-17, "ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement"
YES (Past error)>>Error was detected in the ECM branch line.
NO
>> Repair the power supply and the ground circuit.
ECM harness connector
Resistance (
Ω)
Connector No.
Terminal No.
E10
98
97
Approx. 108 – 132
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст