Nissan Maxima. Manual — part 29
ADP-108
< DTC/CIRCUIT DIAGNOSIS >
TELESCOPIC MOTOR
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit.
3. Check continuity between automatic drive positioner control unit
harness connector and telescopic motor harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-170, "Removal and Installation"
NO
>> Repair or replace harness.
Automatic drive positioner control
unit
Telescopic motor
Continuity
Connector
Terminal
Connector
Terminal
M67 (A)
29
M73 (B)
2
Yes
26
1
ALJIA0444ZZ
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M67 (A)
29
No
26
DOOR MIRROR MOTOR
ADP-109
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DOOR MIRROR MOTOR
Description
INFOID:0000000010051815
It makes mirror face operate from side to side and up and down with the electric power that automatic drive
positioner control unit supplies.
Component Function Check
INFOID:0000000010051816
1.
CHECK DOOR MIRROR MOTOR FUNCTION
Check the operation with “MIRROR MOTOR RH” and “MIRROR MOTOR LH” in “ACTIVE TEST” mode with
CONSULT.
ADP-33, "CONSULT Function (AUTO DRIVE POS.)"
.
Is the inspection result normal?
YES
>> Door mirror motor function is OK.
NO
>> Refer to
ADP-109, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010051817
Regarding Wiring Diagram information, refer to
1.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES
>> Refer to
ADP-111, "Component Inspection"
NO
>> GO TO 2
2.
CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir-
ror.
3. Check continuity between automatic drive positioner control unit
connector and door mirror connector.
Door mirror LH
Terminals
Door mirror re-
mote control
switch condition
Voltage (V)
(Approx.)
(+)
(–)
Door mirror
connector
Terminal
D4 (LH)
D107 (RH)
1
Ground
UP
Battery voltage
Other than above
0
2
LEFT
Battery voltage
Other than above
0
3
DOWN / RIGHT
Battery voltage
Other than above
0
ALJIA0445ZZ
Automatic drive
positioner control
unit connector
Terminal
Door mirror LH
connector
Terminal
Continuity
M63 (A)
12
D4 (B)
3
Yes
23
1
24
2
ALJIA0446ZZ
ADP-110
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR MOTOR
Door mirror RH
4. Check continuity between automatic drive positioner control unit
connector and ground.
Door mirror LH
Door mirror RH
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit
connector and ground.
Door mirror LH
Automatic drive posi-
tioner control unit con-
nector
Terminal
Door mirror
RH connector
Terminal
Continuity
M63 (A)
10
D107 (B)
1
Yes
11
2
22
3
ALJIA0447ZZ
Automatic drive positioner control unit con-
nector
Terminal
Ground
Continuity
M63 (A)
12
No
23
24
Automatic drive positioner control unit con-
nector
Terminal
Ground
Continuity
M63 (A)
10
No
11
22
Terminals
Mirror switch
condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control
unit connector
Terminal
M63
12
Ground
DOWN / RIGHT
Battery voltage
Other than above
0
23
UP
Battery voltage
Other than above
0
24
LEFT
Battery voltage
Other than above
0
ALJIA0448ZZ
DOOR MIRROR MOTOR
ADP-111
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Door mirror RH
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-170, "Removal and Installation"
.
4.
CHECK DOOR MIRROR MOTOR
Check door mirror motor.
ADP-111, "Component Inspection"
Is the inspection result normal?
YES
>> Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace door mirror actuator. Refer to
MIR-19, "Removal and Installation"
.
Component Inspection
INFOID:0000000010051818
1.
CHECK DOOR MIRROR MOTOR-I
Check that door mirror motor does not trap foreign objects and does not have any damage.
.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Replace door mirror actuator. Refer to
MIR-19, "Removal and Installation"
.
2.
CHECK DOOR MIRROR MOTOR-II
1. Turn ignition switch OFF.
2. Disconnect door mirror.
3. Apply 12V to each power supply terminal of door mirror motor.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace door mirror actuator. Refer to
MIR-19, "Removal and Installation"
.
Terminals
Mirror switch con-
dition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner con-
trol unit connec-
tor
Terminal
M63
10
Ground
UP
Battery voltage
Other than above
0
11
LEFT
Battery voltage
Other than above
0
22
DOWN / RIGHT
Battery voltage
Other than above
0
ALJIA0449ZZ
Door mirror connector
Terminal
Operational direction
(+)
(–)
D4 (LH)
D107 (RH)
3
2
RIGHT
2
3
LEFT
1
3
UP
3
1
DOWN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст