Nissan Maxima. Manual — part 1038
FRONT SEAT
SE-125
< REMOVAL AND INSTALLATION >
[W/O CLIMATE CONTROLLED SEATS]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Passenger Seat
AWJIA0926ZZ
1.
Seatback board
2.
Seatback board clip
3.
Headrest
4.
Seat harness
5.
Seat cushion inner finisher inside (RH) 6.
Recline device inner cover
7.
Seat cushion outer finisher (RH) 8.
Seat recline knob
9.
Seat slide and lifter switch knob
10.
Power seat switch
11.
Seat cushion assembly
12. Seat cushion front finisher
13.
Front slide cover
14.
Seat frame assembly
15. Seat cushion outer finisher (LH)
16
Recline mechanism inner cover
17.
Seat cushion inner finisher inside (LH) 18. Seat belt buckle
19.
Seatback assembly
20.
Seatback pad
21. Seatback trim
22.
Seatback frame
23.
Chute rod
24. Side air bag module
25.
Rear slide cover
26.
Headrest holder (locked)
27. Headrest holder (free)
SE-126
< REMOVAL AND INSTALLATION >
[W/O CLIMATE CONTROLLED SEATS]
FRONT SEAT
Removal and Installation
INFOID:0000000009468171
REMOVAL
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat repair. It can lead to per-
sonal injury if the side air bag module should accidentally deploy.
CAUTION:
• When removing or installing the seat trim, handle it carefully to keep dirt out and to avoid damage.
• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-
tor with the side air bag module connector. Such an error may cause the air bag module to deploy.
• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
• After the front side air bag module inflates, the front seatback assembly must be replaced.
• When removing and installing the seat, use shop cloths to protect components from damage.
• Before removing the front seat, turn the ignition switch OFF, disconnect both battery terminals and
wait at least three minutes.
1. Slide the seat to the full froward position.
2. Remove the rear slide covers.
a. Release the pawls (A).
b. Remove the rear slide covers.
3. Remove the rear mount bolts.
4. Slide the seat to the full rearward position.
5. Remove the front slide covers.
6. Remove the front mount bolts.
7. Disconnect the negative and positive battery terminals and wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
ALIIA0356ZZ
ALIIA0324ZZ
ALIIA0323ZZ
FRONT SEAT
SE-127
< REMOVAL AND INSTALLATION >
[W/O CLIMATE CONTROLLED SEATS]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
8. Disconnect the harness connector under the seat and remove harness clips.
9. Remove seat from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Make sure that the seat harness or the floor trim is not damaged during installation.
NOTE:
• When installing the LH front seat, tighten the bolts in the order
shown.
• When installing the RH front seat, tighten the bolts in the order
shown.
LH front seat bolt torque
: 49 Nm (5.0 kg-m, 36 ft-lb)
LIIA2853E
RH front seat bolt torque
: 49 Nm (5.0 kg-m, 36 ft-lb)
LIIA2854E
SE-128
< REMOVAL AND INSTALLATION >
[W/O CLIMATE CONTROLLED SEATS]
REAR SEAT
REAR SEAT
Exploded View - Fixed Seatback
INFOID:0000000009468172
Removal and Installation
INFOID:0000000009468173
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
SEAT CUSHION ASSEMBLY
Removal
1.
Headrest
2.
Headrest holder (free)
3.
Headrest holder (locked)
4.
Bumper
5.
Seatback assembly
6.
Seatback trim
7.
Seatback pad
8.
Seat cushion trim
9.
Seat cushion pad
10. Seat cushion wire cover
11. Seat cushion lock
12. Seat cushion assembly
AWJIA0941ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст