Nissan Maxima. Manual — part 603
EXL-154
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000009465275
Removal and Installation
INFOID:0000000009465276
FRONT COMBINATION LAMP
Removal
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1. Remove the front bumper fascia. Refer to
EXT-16, "Removal and Installation"
.
2. Remove the front combination lamp bolts.
3. Remove the harness clips from the front combination lamp assembly.
4. Pull out the front combination lamp toward the front of vehicle.
5. Disconnect the harness connectors from the front combination lamp and remove.
Installation
Installation is in the reverse order of removal.
NOTE:
After installation, perform headlamp aiming adjustment. Refer to
XENON BULB
Removal
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off, a burn injury may result.
CAUTION:
• After installing the bulb, install the plastic cover and the bulb socket securely for watertightness.
• Do not touch bulb glass with your hand or keep other grease and oily substances away from bulb
glass.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
• Disconnect the battery negative terminal or remove the fuse.
1. Remove the front combination lamp. Refer to
EXL-154, "Removal and Installation"
.
1.
Front combination lamp
ALLIA0897ZZ
FRONT COMBINATION LAMP
EXL-155
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2. Remove screw from cover and rotate the plastic cover counterclockwise and unlock from the front combi-
nation lamp.
3. Rotate the xenon bulb socket counterclockwise and unlock from
the front combination lamp.
4. Unlock the retaining spring and remove the xenon bulb from the
front combination lamp.
CAUTION:
Do not break the xenon bulb ceramic tube when replacing
the bulb.
Installation
Installation is in the reverse order of removal.
HALOGEN BULB (HIGH BEAM)
Removal
1. Remove the front combination lamp. Refer to
EXL-154, "Removal and Installation"
.
2. Rotate the bulb socket counterclockwise and unlock from the front combination lamp.
3. Remove the bulb from the bulb socket.
Installation
Installation is in the reverse order of removal.
FRONT TURN SIGNAL LAMP BULB
Removal
1. Remove the front combination lamp. Refer to
EXL-154, "Removal and Installation"
.
2. Rotate the bulb socket counterclockwise and unlock from the front combination lamp.
3. Remove the bulb from the bulb socket.
Installation
Installation is in the reverse order of removal.
FRONT SIDE MARKER LAMP BULB
Removal
1. Remove the front combination lamp. Refer to
EXL-154, "Removal and Installation"
.
2. Rotate the bulb socket counterclockwise and unlock from the front combination lamp.
3. Remove the bulb from the bulb socket.
Installation
Installation is in the reverse order of removal.
JPLIA0814ZZ
EXL-156
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT FOG LAMP
FRONT FOG LAMP
Exploded View
INFOID:0000000009465277
Removal and Installation
INFOID:0000000009465278
FRONT FOG LAMP
Removal
1. Remove the front bumper fascia. Refer to
EXT-16, "Removal and Installation"
.
2. Disconnect the harness connector from the fog lamp.
3. Remove the front fog lamp bolts.
4. Remove the front fog lamp.
Installation
Installation is in the reverse order of removal.
NOTE:
After installation, perform front fog lamp aiming adjustment. Refer to
EXL-153, "Aiming Adjustment Proce-
.
FRONT FOG LAMP BULB
Removal
WARNING:
Do not touch bulb with your hand while it is on or right after being turned off, a burn injury may result.
CAUTION:
• Do not touch bulb glass with your hand or keep other grease and oily substances away from bulb
glass.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
1.
Front bumper fascia
2.
Front fog lamp
3.
Front fog lamp bracket
4.
Clip
5.
Spring nuts
ALLIA0899ZZ
FRONT FOG LAMP
EXL-157
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1. Remove the front fender protector. Refer to
EXT-24, "Removal and Installation"
2. Disconnect the harness connector (1) from the fog lamp.
3. Rotate the bulb (2) counterclockwise and unlock it.
Installation
Installation is in the reverse order of removal.
ALLIA0894ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст