Nissan Maxima. Manual — part 1215
TPMS
WT-49
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SYMPTOM DIAGNOSIS
TPMS
Symptom Table
INFOID:0000000010046362
Symptom
Reference
Low tire pressure warning lamp does not come on when ignition switch is turned ON.
Low tire pressure warning lamp stays on when ignition switch is turned ON.
Low tire pressure warning lamp flashes when ignition switch is turned ON.
Hazard warning lamps flash when ignition switch is turned ON.
ID registration cannot be completed.
WT-50
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
Low Tire Pressure Warning Lamp Does Not Come On When Ignition Switch Is Turned
On
INFOID:0000000010046363
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
DIAGNOSTIC PROCEDURE
1.
SELF-DIAGNOSTIC RESULT CHECK
Using CONSULT, check display contents of BCM in SELF-DIAGNOSIS.
Is "CAN COMM CIRCUIT" displayed in the self-diagnosis display items?
YES
>> Malfunction in CAN communication system. Refer to
LAN-15, "Trouble Diagnosis Flow Chart"
.
NO
>> GO TO 2
2.
CHECK COMBINATION METER
Check combination meter operation. Refer to
MWI-29, "CONSULT Function (METER/M&A)"
.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Replace combination meter. Refer to
MWI-122, "Removal and Installation"
3.
CHECK LOW TIRE PRESSURE WARNING LAMP
Disconnect BCM harness connector.
Does the low tire pressure warning lamp activate?
YES
>> Replace BCM. Refer to
BCS-79, "Removal and Installation"
NO
>> Check combination meter operation.
LOW TIRE PRESSURE WARNING LAMP STAYS ON
WT-51
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP STAYS ON
Low Tire Pressure Warning Lamp Stays On When Ignition Switch Is Turned On
INFOID:0000000010046364
DIAGNOSTIC PROCEDURE
1.
CHECK BCM CONNECTORS
1. Turn ignition switch OFF.
2. Disconnect BCM harness connectors.
3. Check terminals for damage or loose connections.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace damaged parts.
2.
CHECK BCM POWER SUPPLY AND GROUND CIRCUITS
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-79, "Removal and Installation"
NO
>> Repair BCM circuits.
WT-52
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP BLINKS
LOW TIRE PRESSURE WARNING LAMP BLINKS
Low Tire Pressure Warning Lamp Flashes When Ignition Switch Is Turned On
INFOID:0000000010046365
Regarding Wiring Diagram information, refer to
.
NOTE:
If low tire pressure warning lamp flashes as shown, the system is normal.
Flash Mode A
• This mode shows transmitter status is OFF-mode.
Carry out transmitter wake up operation. Refer to
DIAGNOSTIC PROCEDURE
1.
CHECK BCM CONNECTORS
1. Turn ignition switch OFF.
2. Disconnect BCM harness connectors.
3. Check terminals for damage or loose connections.
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Repair or replace damaged parts.
2.
CHECK TIRE PRESSURE WARNING CHECK CONNECTOR CIRCUIT
Check continuity between BCM harness connector M18 terminal 57 and ground.
Is the inspection result normal?
YES
BCS-79, "Removal and Installa-
.
NO
>> Repair circuit for short to ground.
SEIA0347E
Continuity should not exist.
ALEIA0008ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст