Nissan Maxima. Manual — part 375
DOOR
DLK-219
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Check the clearance and surface height between rear door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
LONGITUDINAL CLEARANCE
1. Remove the center pillar body side trim. Refer to
IP-14, "Removal and Installation"
.
2. Loosen the rear door upper hinge nuts.
3. Loosen the rear door lower hinge bolts.
1.
Front door assembly
2.
Rear door assembly
3.
Body side outer
AWKIA1545GB
Section
Item
Measurement
Standard
A-A
C
Clearance
4.25
± 1.0 (0.17 ± 0.04)
D
Surface height
0.0
± 1.0 (0.0 ± 0.04)
B-B
E
Clearance
4.00
± 1.0 (0.16 ± 0.04)
F
Surface height
0.0
± 1.0 (0.0 ± 0.04)
DLK-220
< REMOVAL AND INSTALLATION >
DOOR
4. Raise or lower the door at the rear edge to adjust.
5. Tighten the rear door lower hinge bolts.
6. Tighten the rear door upper hinge nuts.
7. Install the center pillar body side trim. Refer to
IP-14, "Removal and Installation"
SURFACE HEIGHT ADJUSTMENT
1. Loosen the rear door hinge nuts (door side).
2. Move the top and or the bottom in or out as necessary until it is within specifications provided.
3. Tighten the rear door hinge nuts (door side) to specification.
DOOR LOCK
DLK-221
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK
FRONT DOOR LOCK
FRONT DOOR LOCK : Exploded View
INFOID:0000000009471773
FRONT DOOR LOCK : Removal and Installation
INFOID:0000000009471774
REMOVAL
1. Remove front door finisher. Refer to
INT-18, "Removal and Installation"
2. Remove front door module assembly. Refer to
INT-18, "Removal and Installation"
3. Disconnect door antenna and door request switch connector
and remove harness clamp on outside handle bracket.
1.
Door key cylinder outside handle escutcheon
assembly (drivers side)
Outside handle escutcheon (passenger side)
2.
Rear gasket
3.
Striker
4.
Door key cylinder rod (driver side)
5.
Front door lock assembly
6.
Inside handle
7.
Outside handle bracket
8.
Front gasket
9.
Outside handle
A.
Bolt
Front
AWKIA1809GB
PIIB5807E
DLK-222
< REMOVAL AND INSTALLATION >
DOOR LOCK
4. Remove door side grommet, and loosen bolt from grommet
hole.
5. Disconnect the door key cylinder rod from the door key cylinder.
6. While pulling outside handle (1), remove door key cylinder
assembly (2) (driver side) or outside handle escutcheon (pas-
senger side) (2).
7. While pulling outside handle (1), slide toward rear of vehicle (2)
to remove outside handle.
8. Remove front gasket and rear gasket.
9. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
10. Separate the outside handle cable connection from the outside handle bracket.
11. Remove door lock assembly bolts.
12. Disconnect door lock actuator connector, and then remove door lock assembly.
13. Remove key rod from door lock assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
JMKIA2094ZZ
JMKIA0560ZZ
PIIB5810E
JMKIA2303ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст