Nissan Maxima. Manual — part 1118
STEERING WHEEL
ST-17
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
REMOVAL AND INSTALLATION
STEERING WHEEL
Removal and Installation
INFOID:0000000009465773
REMOVAL
NOTE:
When removing spiral cable, use tape so that the case and rotating part keep aligned. This will prevent neutral
position alignment procedure during spiral cable installation.
1. Set steering wheel to the straight-ahead position.
2. Remove driver air bag module. Refer to
SR-12, "Removal and Installation"
.
3. Remove steering wheel lock nut after steering is locked.
4. Remove steering wheel using Tool (A).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not rotate spiral cable freely or excessively when the steering wheel is removed. Doing so may
cause spiral cable damage.
NOTE:
• Check the spiral cable neutral position after replacing or rotating spiral cable. Refer to
.
• Tighten the steering wheel lock nut to specification. Refer to
.
Tool number (A) : ST27180001 (J-25726-A)
JSGIA0341ZZ
ST-18
< REMOVAL AND INSTALLATION >
TILT MOTOR
TILT MOTOR
Exploded View
INFOID:0000000009465774
Removal and Installation
INFOID:0000000009465775
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-19, "Removal and Installation"
.
2. Remove lower knee protector (LH) bolts (A) and the lower knee
protector (LH) (B).
3. Telescope the steering wheel to the full out position and tilt to highest position.
NOTE:
If either function is inoperative you can do this manually prior to installation.
4. Remove the steering column covers. Refer to
IP-11, "Removal and Installation"
.
NOTE:
1.
Steering column assembly
2.
Telescope motor
3.
Telescope motor link bracket
4.
Tilt motor
5.
Tilt motor bolt cap
ALGIA0054GB
ALGIA0050ZZ
TILT MOTOR
ST-19
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
The tilt/telescope switch can remain attached to the side cover.
5. Remove the tilt motor as follows.
1. Disconnect the harness connector (A) from the tilt motor.
2. Remove the tilt motor link bolts (B).
3. Remove the tilt motor bolt (A) from the RH side of column.
4. Remove the tilt motor (B).
NOTE:
If the steering wheel could not be tilted to the highest position,
manually tilt steering wheel to the highest position.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• When installing the tilt motor link bolts, manually move steering wheel up and down to align the bolt holes.
• Inform customer that they will need to reset their Automatic Drive Positioner (ADP) settings.
ALGIA0051ZZ
ALGIA0052ZZ
ST-20
< REMOVAL AND INSTALLATION >
TELESCOPIC MOTOR
TELESCOPIC MOTOR
Exploded View
INFOID:0000000009465776
Removal and Installation
INFOID:0000000009465777
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-19, "Removal and Installation"
.
2. Remove lower knee protector (LH) bolts (A) and the lower knee
protector (LH) (B).
3. Telescope the steering wheel to the full out position and tilt to highest position.
NOTE:
If either function is inoperative you can do this manually prior to installation.
4. Remove the steering column covers. Refer to
IP-11, "Removal and Installation"
.
NOTE:
1.
Steering column assembly
2.
Telescope motor
3.
Telescope motor link bracket
4.
Tilt motor
5.
Tilt motor bolt cap
ALGIA0054GB
ALGIA0050ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст