Nissan Maxima. Manual — part 895
PCS-60
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B261A PUSH-BUTTON IGNITION SWITCH
B261A PUSH-BUTTON IGNITION SWITCH
Description
INFOID:0000000010049444
IPDM E/R transmits the push-button ignition switch status via CAN communication to BCM. BCM receives
push-button ignition switch status by hardwire input. BCM compares the 2 signals for mismatch.
DTC Logic
INFOID:0000000010049445
DTC DETECTION LOGIC
NOTE:
• If DTC B261A is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B261A is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press the push-button ignition switch under the following conditions and wait for at least 1 second.
-
CVT selector lever is in the P position
-
Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000010049446
Regarding Wiring Diagram information, refer to
1.
CHECK PUSH-BUTTON IGNITION SWITCH OPERATION
Press push-button ignition switch and check if it turns to ON.
Does ignition switch turn to ON?
YES
>> GO TO 2
NO
>> GO TO 4
2.
CHECK IGNITION SWITCH OUTPUT SIGNAL (IPDM E/R)
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B261A
PUSH-BUTTON
IGNITION
SWITCH
BCM detects the mismatch between the following for 1
second or more
• Push-button ignition switch status
• Push-button ignition switch status from IPDM E/R (CAN)
• Harness or connectors
(Push-button ignition switch circuit is
open or shorted)
• Between BCM and push-button igni-
tion switch
• Between IPDM E/R and push-button
ignition switch
PCS
B261A PUSH-BUTTON IGNITION SWITCH
PCS-61
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch.
3. Check voltage between IPDM E/R harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Replace IPDM E/R. Refer to
PCS-35, "Removal and Installation"
.
3.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (IPDM E/R)
1. Disconnect IPDM E/R and BCM.
2. Check continuity between IPDM E/R harness connector (A) and
push-button ignition switch harness connector (B).
3. Check continuity between IPDM E/R harness connector and
ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Repair or replace harness.
4.
CHECK IGNITION SWITCH OUTPUT SIGNAL (BCM)
1. Disconnect push-button ignition switch.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace BCM. Refer to
BCS-79, "Removal and Installation"
5.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT (BCM)
1. Disconnect BCM and IPDM E/R.
2. Check continuity between BCM harness connector and push-button ignition switch harness connector.
Terminals
Voltage (V)
(+)
(-)
IPDM E/R
Ground
Connector
Terminal
E18
28
Battery voltage
ALMIA0090ZZ
IPDM E/R
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
E18 (A)
28
M38 (B)
4
Yes
ALMIA0091ZZ
IPDM E/R
Ground
Continuity
Connector
Terminal
E18
28
No
ALMIA0092ZZ
Terminals
Voltage (V)
(+)
(-)
BCM
Ground
Connector
Terminal
M21
140
Battery voltage
PCS-62
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B261A PUSH-BUTTON IGNITION SWITCH
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6
NO
>> Repair or replace harness.
6.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
>> Inspection End.
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M21
140
M38
4
Yes
BCM
Ground
Continuity
Connector
Terminal
M21
140
No
PCS
POWER SUPPLY AND GROUND CIRCUIT
PCS-63
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER SUPPLY AND GROUND CIRCUIT
BCM
BCM : Diagnosis Procedure
INFOID:0000000010049506
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSE AND FUSIBLE LINK
Check if the following BCM fuses or fusible link are blown.
Is the fuse or fusible link blown?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit.
NO
>> GO TO 2
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Is the measurement normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Inspection End.
NO
>> Repair or replace harness.
BCM : Special Repair Requirement
INFOID:0000000010049507
1.
REQUIRED WORK WHEN REPLACING BCM
Initialize control unit. Refer to
BCS-5, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) :
Terminal No.
Signal name
Fuse and fusible link No.
1
Battery power supply
H
11
10
24
7
Terminals
Voltage
(Approx.)
(+)
(
−)
BCM
Ground
Connector
Terminal
M16
1
Battery voltage
M17
11
M18
24
BCM
Ground
Continuity
Connector
Terminal
M17
13
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст