Nissan Maxima. Manual — part 662
FAX-24
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT DRIVE SHAFT
1. Add grease (Genuine NISSAN Grease or equivalent) into joint
sub-assembly serration hole until grease begins to ooze from
ball groove and serration hole. After inserting grease, use a
shop cloth to wipe off old grease that has oozed out.
2. Cover serrated part of shaft with tape. Install new boot and boot
band onto shaft. Be careful not to damage boot.
CAUTION:
Do not reuse boot band and boot.
3. Remove protective tape wound around serrated part of shaft.
4. Attach new circlip to shaft. The circlip must fit securely into shaft
groove. Attach nut to joint sub-assembly.
Use a suitable tool to press-fit.
CAUTION:
Do not reuse circlip.
5. Insert the amount of new grease (Genuine NISSAN Grease or equivalent) listed below into housing from
large end of boot.
6. Install boot securely into grooves (indicated by * marks) as
shown.
CAUTION:
• If there is grease on boot mounting surfaces (indicated by
* marks) of shaft and housing, boot may come off.
Remove all grease from surfaces.
• Do not reuse boot.
7. Make sure boot installation length (L) is the specified length,
indicated below. Insert a suitable tool into the large end of boot.
Bleed air from boot to prevent boot deformation.
CAUTION:
• Boot may break if boot installation length is less than standard value.
• Be careful that the tool does not contact inside surface of boot.
SDIA1127E
SFA800
RAC0049D
Grease quantity
: Refer to
.
Boot installation length (L)
: Refer to
JPDIF0142ZZ
FRONT DRIVE SHAFT
FAX-25
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
8. Install new large and small boot bands securely using Tool.
CAUTION:
• Do not reuse boot bands.
• Secure boot band so that dimension (M) meets specifica-
tion as shown.
9. After installing housing and shaft, rotate boot to check whether or not the actual position is correct. If boot
position is not correct, remove old boot bands then reposition the boot and secure with new boot bands.
Damper
1. Use new damper bands for installation.
CAUTION:
Do not reuse damper bands.
2. Install damper from stationary-joint side while holding it securely.
Tool number
: KV40107300 (
—
)
RAC1133D
Dimension (M)
.
AWDIA0598ZZ
(A)
: Refer to
.
(B)
: Refer to
.
SFA313B
FAX-26
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000009471153
Drive Shaft
INFOID:0000000009471154
*: Boot installation grooves
Dynamic Damper
INFOID:0000000009471155
NOTE:
Measured from wheel side.
Axial end play limit
0.05 mm (0.002 in) or less
Joint type
Wheel side
Transaxle side
LH
RH
LH
RH
Grease quantity
170 - 190 g (6.00 - 6.70 oz)
155 - 175 g (5.47 - 6.17 oz)
Boot installation
length (L)
158.6 mm (6.42 in)
163.7 mm (6.44 in)
JPDIF0142ZZ
JPDIF0144ZZ
(A)
LH
207 - 213 mm (8.15 -8.39 in)
RH
202 - 208 mm (7.95 - 8.19 in)
(B)
70 mm (2.76 in)
SFA313B
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-27
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Boot Bands
INFOID:0000000009471156
Unit: mm (in)
Dimension (M)
7.0 (0.28)
AWDIA0598ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст