Nissan Maxima. Manual — part 1133
STR-16
< SYMPTOM DIAGNOSIS >
[VQ35DE]
STARTING SYSTEM
SYMPTOM DIAGNOSIS
STARTING SYSTEM
Symptom Table
INFOID:0000000009465007
Symptom
Reference
No normal cranking
STR-2, "Work Flow (With GR8-1200 NI)"
.
Starter motor does not rotate
PRECAUTIONS
STR-17
< PRECAUTION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009465008
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
STR-18
< PREPARATION >
[VQ35DE]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009465009
The actual shapes of the tools may differ from those illustrated here.
Commercial Service Tools
INFOID:0000000009465010
Tool number
(TechMate No.)
Tool name
Description
—
(—) Model GR8-1200 NI
Multitasking battery and electrical di-
agnostic station
Tests batteries, starting and charging sys-
tems and charges batteries.
For operating instructions, refer to diagnostic
station instruction manual.
AWIIA1239ZZ
Tool name
Description
Power tools
Loosening nuts, screws and bolts
PIIB1407E
STARTER MOTOR
STR-19
< REMOVAL AND INSTALLATION >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
REMOVAL AND INSTALLATION
STARTER MOTOR
Removal and Installation
INFOID:0000000009465011
REMOVAL
1. Remove the battery tray. Refer to
PG-68, "Removal and Installation (Battery Tray)"
2. Disconnect the battery cable (A) and starter harness connector.
3. Remove the starter bolts, then remove the starter.
INSTALLATION
Installation is in the reverse order of removal.
• Reset electronic systems as necessary. Refer to
PG-5, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Special Repair Requirement"
CAUTION:
Carefully tighten the battery cable nut.
AWBIA0988ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст