Nissan Maxima. Manual — part 372
HOOD
DLK-207
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5. Connect the hood lock release cable to the hood lock assembly.
6. Install the bolts to hood lock release handle.
7. Loosely install the hood lock assembly.
8. Perform hood fitting adjustment. Refer to
DLK-203, "HOOD ASSEMBLY : Adjustment"
9. Perform the hood lock control inspection. Refer to
DLK-207, "HOOD LOCK CONTROL : Inspection"
HOOD LOCK CONTROL : Inspection
INFOID:0000000009471760
INSPECTION
CAUTION:
If the hood lock cable is bent or deformed, replace it.
1. Check that the secondary latch is properly engaged with the secondary striker with hood's own weight.
2. While operating the hood lock release handle, carefully check that the front end of the hood is raised by
approx. 20 mm (0.8 in). Also check that the hood lock release handle returns to the original position.
3. Check that the hood lock release handle operating force is 49 N (5.0 kg, 11.0 lb) or below.
4. Install so the static closing force of the hood assembly is 315 – 490 N·m (32.1– 50.0 kg-m, 70.8 - 110.2 ft-
lb).
5. Check the hood lock assembly lubrication condition. If neces-
sary, apply a suitable multi-purpose grease as shown.
: Grease
HOOD STAY
PIIB5802E
Bolts
10 N·m (1.0 kg-m, 7ft-lb)
1.
Hood striker
2.
Primary latch
3.
Secondary latch
4.
Secondary striker
A. 20 mm (0.8 in)
B. 6.8 mm (0.27 in)
PIIB5794E
ALKIA0028GB
DLK-208
< REMOVAL AND INSTALLATION >
HOOD
HOOD STAY : Disposal
INFOID:0000000009471761
1. Fix hood stay (1) using a vise (C).
2. Using hacksaw (A) slowly make 2 holes in the hood stay (1), in
numerical order as shown.
CAUTION:
• When cutting a hole on hood stay, always cover hacksaw
with a shop cloth (B) to avoid scattering metal fragments
or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
JMKIA3336ZZ
A: 20 mm (0.8 in)
B: Cut at the groove.
JMKIA3609ZZ
RADIATOR CORE SUPPORT
DLK-209
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RADIATOR CORE SUPPORT
Exploded View
INFOID:0000000009471762
Removal and Installation
INFOID:0000000009471763
REMOVAL
1. Remove front bumper. Refer to
EXT-16, "Removal and Installation"
2. Remove front combination lamps (LH/RH). Refer to
EXL-154, "Removal and Installation"
(Xenon Type),
EXL-318, "Removal and Installation"
(Halogen Type).
3. Remove the radiator cooling fans. Refer to
CO-16, "Removal and Installation"
.
4. Remove the radiator. Refer to
CO-14, "Removal and Installation"
.
5. Remove the hood lock control. Refer to
DLK-205, "HOOD LOCK CONTROL : Removal and Installation"
6. Remove crash zone sensor. Refer to
SR-27, "Removal and Installation"
.
7. Disconnect power steering tube assembly from clips and position aside. Refer to
.
8. Remove the horns. Refer to
HRN-7, "Removal and Installation"
9. Remove the harness clips from the radiator core support assembly and position the harness aside.
1.
Radiator core support
a.
Bolts
AWKIA2595ZZ
DLK-210
< REMOVAL AND INSTALLATION >
RADIATOR CORE SUPPORT
10. Remove the bolts and the radiator core support.
INSTALLATION
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст