Nissan Maxima. Manual — part 692
GW-18
< REMOVAL AND INSTALLATION >
FRONT REGULATOR
FRONT REGULATOR
Exploded View
INFOID:0000000009471568
Removal and Installation
INFOID:0000000009471569
REMOVAL
1. Remove the front door finisher. Refer to
INT-18, "Removal and Installation"
2. Remove the adhesive bolt hole covers.
3. Reconnect the window switch to raise/lower the door glass until
the door glass bolts (A) can be seen.
4. Remove the door glass bolts (A).
1. Door panel
2.
Door glass
3.
Regulator assembly
4.
Door module assembly
5.
Window motor
AWKIA1770ZZ
ALKIA1623GB
FRONT REGULATOR
GW-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
5. Raise the door glass and hold with a suction lifter (A).
6. Disconnect the harness connector (A) from the window motor.
7. Remove the door module assembly mounting bolts.
8. Remove the door module assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Wire wear
• Regulator deformation
• Grease condition for each sliding part
Apply multi-purpose grease at the locations shown.
INSTALLATION
Installation is in the reverse order of removal.
• Make sure the glass is securely set into the glass run groove.
• Lower the glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)] and make sure the clearance to the sash is
parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting bolts,
guide rail mounting bolts, and glass and guide rail mounting bolts to adjust the glass position.
PIIB3510J
ALKIA1624GB
ALKIA1625GB
ALKIA1627GB
GW-20
< REMOVAL AND INSTALLATION >
FRONT REGULATOR
Inspection and Adjustment
INFOID:0000000009471570
SYSTEM INITIALIZATION
If any of the following work has been done, initialize the system. Refer to
WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement"
• Electric power supply to power window switch or motor is interrupted by blown fuse or disconnecting battery
cable, etc.
• Removal and installation of the regulator assembly.
• Removal and installation of the motor from the regulator assembly.
• Removal and installation of the harness connector of the power window switch.
• Operate the regulator assembly as a unit.
• Removal and installation of the door glass.
• Removal and installation of the door glass run.
• Window is partly opened and/or closed many times without being fully closed.
Initialization
After installing each component to the vehicle, follow the steps below.
1. Disconnect the negative battery terminal or disconnect the power window switch harness connector tem-
porarily, then reconnect after at least 1 minute.
2. Turn ignition switch ON.
3. Open the window fully by operating the power window switch. (Exclude this procedure if the window is
already fully opened.)
4. Fully raise the power window switch in up direction (auto close position) and hold. Keep holding the switch
even when window is completely closed and then release after 3 seconds have passed.
5. Inspect the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation. In this case, initialize the
system.
INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM
To inspect the anti-pinch system, refer to
PWC-7, "ADDITIONAL SERVICE WHEN REMOVING BATTERY
NEGATIVE TERMINAL : Special Repair Requirement"
.
REAR DOOR GLASS
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000009471571
Removal and Installation
INFOID:0000000009471572
REMOVAL
1. Remove the rear door finisher. Refer to
INT-21, "Removal and Installation"
.
2. Position the vapor barrier aside.
3. Temporarily reconnect the power window switch and raise/lower
the door window until the glass bolts can be seen.
4. Remove the glass bolts, and place the glass on the inner bottom
of the panel.
1. Door glass run
2. Door panel
3. Window motor
4. Regulator assembly
5. Partition glass run
6. Partition glass
7. Partition sash
8. Door glass
AWKIA1771ZZ
ALKIA1629GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст