Nissan Maxima. Manual — part 847
MWI
MWI-3
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
THE DOOR OPEN WARNING CONTINUES
DISPLAYING, OR DOES NOT DISPLAY . .
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
THE AMBIENT TEMPERATURE DISPLAY IS
INCORRECT . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . .
NORMAL OPERATING CONDITION . . . ...
COMPASS . . . . . . . . . . . . . . . ...
COMPASS : Description . . . . . . . . . ...
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . ...
Precaution for Work . . . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . .
Commercial Service Tools . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
COMBINATION METER . . . . . . . . .
Removal and Installation . . . . . . . . . ...
METER CONTROL SWITCH . . . . . . ..
Removal and Installation . . . . . . . . . ...
UNIT DISASSEMBLY AND ASSEMBLY ..
COMBINATION METER . . . . . . . . .
MWI-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000010049525
OVERALL SEQUENCE
DETAILED FLOW
1.
CONFIRM SYMPTOM
Confirm symptom or customer complaint.
>> GO TO 2
2.
CHECK SELF-DIAGNOSIS OPERATION OF COMBINATION METER
Perform self-diagnosis of combination meter. Refer to
MWI-29, "Diagnosis Description"
.
Does self-diagnosis mode operate?
YES
>> GO TO 3
NO
>> Check power supply and ground circuit of combination meter. Refer to
. Then, GO TO 4
3.
CHECK COMBINATION METER (CONSULT)
AWNIA2484GB
MWI
DIAGNOSIS AND REPAIR WORKFLOW
MWI-5
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Select “METER/M&A” on CONSULT and perform “SELF-DIAGNOSIS” of combination meter. Refer to
29, "CONSULT Function (METER/M&A)"
.
Self-diagnostic results content
No malfunction detected>>Repair or replace the cause of symptom. Then, GO TO 4
Malfunction detected>>Refer to
. Then, GO TO 4
4.
CONFIRM OPERATION
Does the combination meter operate normally?
YES or NO
YES
>> Inspection End.
NO
>> GO TO 1
MWI-6
< SYSTEM DESCRIPTION >
METER SYSTEM
SYSTEM DESCRIPTION
METER SYSTEM
METER SYSTEM
METER SYSTEM : System Diagram
INFOID:0000000010049526
METER SYSTEM : System Description
INFOID:0000000010049527
COMBINATION METER
• Speedometer, odo/trip meter, tachometer, fuel gauge, water temperature gauge and information display are
controlled by the unified meter control unit, which is built into the combination meter.
• Warning and indicator lamps are controlled by the unified meter control unit and by components connected
directly to the combination meter.
• Digital meter is adopted for odo/trip meter.*
*The record of the odometer is kept even if the battery cable is disconnected. The record of the trip meter is
erased when the battery cable is disconnected.
• Odo/trip meter and information display segments can be checked in diagnosis mode.
• Meter/gauge can be checked in diagnosis mode.
AWNIA2688GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст