Nissan Maxima. Manual — part 1175
TM-164
< PERIODIC MAINTENANCE >
[CVT: RE0F09B]
ROAD TEST
ROAD TEST
Description
INFOID:0000000010113962
DESCRIPTION
• The purpose of the test is to determine the overall performance of
CVT and analyze causes of problems.
• The road test consists of the following three parts:
1. “Check Before Engine Is Started”
.
3. “Cruise Test”
.
• Before the road test, familiarize yourself with all test procedures
and items to check.
• Perform tests for all the check items until a malfunction phenome-
non is detected. Perform diagnosis for NG items after the comple-
tion of road tests.
CONSULT SETTING PROCEDURE
• Using CONSULT, perform a cruise test and record the result.
• Print the result and ensure that shifts and lock-ups take place as per Shift Schedule.
1. Touch “Data Monitor” in “Direct Diagnostic Mode” screen.
2. Touch “MAIN SIGNALS” to set recording condition.
3. See “Numerical Display”, “Barchart Display” or “Line Graph Display”.
4. Touch “START”.
5. When performing cruise test. Refer to
6. After finishing cruise test part, touch “RECORD”.
7. Touch “STORE”.
8. Touch “BACK”.
9. Touch “DISPLAY”.
10. Touch “PRINT”.
11. Check the monitor data printed out.
Check before Engine Is Started
INFOID:0000000010113963
1.
CHECK SHIFT POSITION INDICATOR
1. Park vehicle on flat surface.
2. Move selector lever to “P” position.
3. Turn ignition switch OFF. Wait at least 5 seconds.
4. Turn ignition switch ON. (Do not start engine.)
Has shift position indicator been turned ON for about 2 seconds?
YES
>> 1. Turn ignition switch OFF.
2. Perform self-diagnosis and note NG items. Refer to
.
3. Go to
.
NO
>> Stop “Road Test”. Refer to
.
SAT786A
SAT496G
ROAD TEST
TM-165
< PERIODIC MAINTENANCE >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Check at Idle
INFOID:0000000010113964
1.
CHECK STARTING THE ENGINE (PART 1)
1. Park vehicle on flat surface.
2. Move selector lever to “P” or “N” position.
3. Turn ignition switch OFF.
4. Turn ignition switch to “START” position.
Is engine started?
YES
>> GO TO 2.
NO
>> Stop “Road Test”. Refer to
.
2.
CHECK STARTING THE ENGINE (PART 2)
1. Turn ignition switch ON.
2. Move selector lever to “D”, “M”, “DS” or “R” position.
3. Turn ignition switch to “START” position.
Is engine started?
YES
>> Stop “Road Test”. Refer to
.
NO
>> GO TO 3.
3.
CHECK “P” POSITION FUNCTION
1. Move selector lever to “P” position.
2. Turn ignition switch OFF.
3. Release parking brake.
4. Push vehicle forward or backward.
5. Apply parking brake.
Does vehicle move forward or backward?
YES
>> Refer to
. GO TO 4.
NO
>> GO TO 4.
4.
CHECK “N” POSITION FUNCTION
1. Start engine.
2. Move selector lever to “N” position.
3. Release parking brake.
Does vehicle move forward or backward?
YES
>> Refer to
. GO TO 5.
NO
>> GO TO 5.
5.
CHECK SHIFT SHOCK
1. Apply foot brake.
2. Move selector lever to “R” position.
Is there large shock when changing from “N” to “R” position?
YES
>> Refer to
. GO TO 6.
NO
>> GO TO 6.
6.
CHECK “R” POSITION FUNCTION
Release foot brake for several seconds.
Does vehicle creep backward when foot brake is released?
YES
>> GO TO 7.
NO
>> Refer to
. GO TO 7.
7.
CHECK “D” POSITION FUNCTION
Move selector lever to “D”, “DS” and “M” position and check if vehicle creeps forward.
Does vehicle creep forward in all positions?
YES
>> Go to
.
NO
>> Stop “Road Test”. Refer to
.
TM-166
< PERIODIC MAINTENANCE >
[CVT: RE0F09B]
ROAD TEST
Cruise Test
INFOID:0000000010113965
1.
CHECK VEHICLE SPEED WHEN SHIFTING GEARS (PART 1)
1. Drive vehicle for approximately 10 minutes to warm engine oil and CVT fluid up to operating temperature.
2. Park vehicle on flat surface.
3. Move selector lever to “P” position.
4. Start engine.
5. Move selector lever to “D” position.
6. Accelerate vehicle at 2/8 throttle opening and check “Vehicle
Speed When Shifting Gears”.
With CONSULT
-
Read vehicle speed and engine speed. Refer to
cle Speed When Shifting Gears"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
. GO TO 2.
2.
CHECK VEHICLE SPEED WHEN SHIFTING GEARS (PART 2)
1. Park vehicle on flat surface.
2. Move selector lever to “D” position.
3. Accelerate vehicle at 8/8 throttle opening and check “Vehicle
Speed When Shifting Gears”.
With CONSULT
-
Read vehicle speed and engine speed. Refer to
cle Speed When Shifting Gears"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Refer to
. GO TO 3.
3.
CHECK DS MODE FUNCTION
Move to “DS” mode from “D” position.
Does it switch to “DS” mode?
YES
>> GO TO 4.
NO
>> Refer to
. GO TO 4.
4.
CHECK MANUAL MODE FUNCTION
Move to manual mode from “DS” position.
Does it switch to manual mode?
YES
>> GO TO 5.
NO
>> Refer to
. GO TO 5.
5.
CHECK SHIFT UP FUNCTION
During manual mode driving, is upshift from M1
→ M2 → M3 → M4 → M5 → M6 performed?
With CONSULT
• Read vehicle speed and engine speed. Refer to
Is upshifting correctly performed?
YES
>> GO TO 6.
NO
>> Refer to
. GO TO 6.
CVT fluid operating temperature : 50 – 80
°C (122 – 176°F)
SCIA6644E
SCIA4366E
ROAD TEST
TM-167
< PERIODIC MAINTENANCE >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6.
CHECK SHIFT DOWN FUNCTION
During manual mode driving, is downshift from M6
→ M5 → M4 → M3 → M2 → M1 performed?
With CONSULT
• Read vehicle speed and engine speed. Refer to
Is downshifting correctly performed?
YES
>> GO TO 7.
NO
>> Refer to
. GO TO 7.
7.
CHECK ENGINE BRAKE FUNCTION
Check engine brake.
Does engine braking effectively reduce vehicle speed in “M
1
” position?
YES
>> 1. Stop the vehicle.
2. Perform “Self Diagnostic Results” in “TRANSMISSION”.
NO
>> Refer to
. Then continue trouble diagnosis.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст