Nissan Maxima. Manual — part 270
PREPARATION
BRC-101
< PREPARATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009466774
The actual shapes of the tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000009466775
Tool number
(TechMate No.)
Tool name
Description
—
(J-45741)
ABS active wheel sensor tester
Checking operation of ABS active wheel sen-
sor
WFIA0101E
Tool name
Description
1. Flare nut crowfoot
2. Torque wrench
Removing and installing brake piping
a: 10mm (0.39 in)/12mm (0.47 in)
Power tool
Loosening nuts, screws and bolts
S-NT360
PIIB1407E
BRC-102
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
WHEEL SENSORS
REMOVAL AND INSTALLATION
WHEEL SENSORS
Exploded View - Front Wheel Sensor
INFOID:0000000009466776
Removal and Installation - Front Wheel Sensor
INFOID:0000000009466777
CAUTION:
• Be careful not to damage wheel sensor edge and sensor rotor teeth.
• When pulling out the wheel sensor, be careful to turn it as little as possible. Do not pull on the wheel
sensor harness.
• Check if foreign objects such as iron fragments are adhered to the pick-up part of the sensor or to
the inside of the hole for the wheel sensor, or if a foreign object is caught in the surface of the mating
surface for the wheel sensor. Repair as necessary and then install the wheel sensor.
REMOVAL
1. Remove the front wheel and tire using power tools. Refer to
2. Partially remove front wheel fender protector and reposition out of the way. Refer to
3. Disconnect the harness connector from the front wheel sensor.
4. Remove the front wheel sensor harness from the brackets.
5. Remove the front wheel sensor bolt and front wheel sensor from the front wheel hub and bearing assem-
bly.
INSTALLATION
1.
Front wheel sensor
A. Color line (slant line)
B. Front wheel sensor harness connector
Front
ALFIA0320ZZ
WHEEL SENSORS
BRC-103
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Installation is in the reverse order of removal.
CAUTION:
Do not twist rear wheel sensor harness when installing rear
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that rear wheel sensor harness is not twisted
after installation.
Exploded View - Rear Wheel Sensor
INFOID:0000000009466778
Removal and Installation - Rear Wheel Sensor
INFOID:0000000009466779
CAUTION:
• Be careful not to damage wheel sensor edge and sensor rotor teeth.
• When removing the front or rear wheel hub, first remove the wheel sensor from the wheel hub. Fail-
ure to do so may result in damage to the wheel sensor wires making the sensor inoperative.
• Pull out the wheel sensor, being careful to turn it as little as possible. Do not pull on the wheel sen-
sor harness.
• Before installation, check if foreign objects such as iron fragments are adhered to the pick-up part of
the sensor or to the inside of the hole in the wheel hub for the wheel sensor, or if a foreign object is
JPFIC0209ZZ
1.
Rear wheel sensor
A. Rear wheel sensor bracket
B. Clip
C. Rear wheel sensor harness connector
Front
ALFIA0323ZZ
BRC-104
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
WHEEL SENSORS
caught in the surface of the mating surface for the sensor rotor. Clean as necessary and then install
the wheel sensor.
REMOVAL
1. Remove the rear wheel and tire using power tools. Refer to
.
2. Remove the rear stabilizer bar clamps and bushings. Position the stabilizer bar out of the way. Refer to
.
3. Disconnect the harness connector from the rear wheel sensor.
4. Remove the rear wheel sensor harness from the brackets.
5. Remove the rear wheel sensor bolt and rear wheel sensor from the rear wheel hub and bearing assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not twist rear wheel sensor harness when installing rear
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that rear wheel sensor harness is not twisted
after installation.
JPFIC0209ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст