Nissan Maxima. Manual — part 1089
FRONT PASSENGER AIR BAG MODULE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT PASSENGER AIR BAG MODULE
Removal and Installation
INFOID:0000000009471844
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Do not use air tools or electric tools for servicing.
• Always work from the side of air bag module. Do not work from the front of it.
• Always place air bag module with pad side facing upward.
• Do not cause impact to the air bag module by dropping etc. Replace the air bag module if it has been
dropped or sustained an impact.
REMOVAL
1. Disconnect the negative and positive battery terminals, then wait at least 3 minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove the glove box assembly. Refer to
IP-20, "Removal and Installation"
3. Disconnect the harness connector (A) from the front passenger
air bag module.
NOTE:
The figure shows installed condition of the front passenger air
bag module without glove box in place.
4. Remove front passenger air bag module bolt (B) from steering
member (1).
5. Remove the remaining instrument panel from the vehicle. Refer
IP-19, "Removal and Installation"
.
6. Remove the front passenger air bag module screws (A).
: Front
Front passenger air bag
module bolt (B)
: 22.3 N·m (2.3 kg-m, 16 in-
lb)
AWHIA0447ZZ
ALHIA0127GB
SR-18
< REMOVAL AND INSTALLATION >
FRONT PASSENGER AIR BAG MODULE
7. Release the upper and lower front passenger air bag module
tabs (A) from instrument panel and pad assembly (1).
8. Rotate and lift the front passenger air bag module away from the
instrument panel, then remove.
INSTALLATION
CAUTION:
• Do not use old bolts after removal; replace with new bolts.
• Be careful not to damage the harness while installing.
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function
and delete the memory by CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to
1. Install front passenger air bag module to the instrument panel assembly.
2. Install the instrument panel assembly. Refer to
IP-19, "Removal and Installation"
3. Connect the front passenger air bag module harness connector to yellow 4-pin service replacement con-
nector and fasten to mounting bracket.
ALHIA0128ZZ
SIDE CURTAIN AIR BAG MODULE
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE CURTAIN AIR BAG MODULE
Component
INFOID:0000000009471845
Removal and Installation
INFOID:0000000009471846
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes.
• Do not use air tools or electric tools for servicing.
• Always work from the side of air bag module. Do not work from the front of it.
• Always place the curtain air bag module with air bag deployment side facing upward.
• Do not attempt to disassemble side curtain air bag module.
REMOVAL
1. Disconnect the negative and positive battery terminals, then wait at least 3 minutes. Refer to
"Removal and Installation (Battery)"
.
2. Remove the headlining. Refer to
INT-33, "Removal and Installation"
.
3. Disconnect the side curtain air bag module harness connector
(2) from the inflator (1).
1.
Side curtain air bag module tether 2.
Side curtain air bag module assembly 3.
Side curtain air bag module inflator
Front
ALHIA0284ZZ
ALHIA0130ZZ
SR-20
< REMOVAL AND INSTALLATION >
SIDE CURTAIN AIR BAG MODULE
• For installing/removing direct-connect SRS harness connec-
tors. Refer to
SRC-9, "SRS Component Connectors"
.
• Do not repair direct-connect SRS component harness connec-
tors. Refer to
SRC-12, "Trouble Diagnosis Introduction"
4. Remove the bolts, then remove side curtain air bag module
assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to damage the air bag harness.
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case a malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function
and delete the memory by CONSULT.
• If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunc-
tions. Refer to
• Make sure the side curtain air bag module is not twisted at any point along the vehicle when
installed.
• Replace the side curtain air bag module if it has been dropped
or sustained an impact.
PHIA0953J
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст