Nissan Maxima. Manual — part 1063
B210F TRANSMISSION RANGE SWITCH
SEC-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
4. Check voltage between IPDM E/R harness connector E18 termi-
nal 30 and ground under following condition.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
NO
>> GO TO 3.
3.
CHECK TRANSMISSION RANGE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check continuity between IPDM E/R harness connector E18 (B)
terminal 72 and TCM harness connector F15 (A) terminal 20.
4. Check continuity between TCM harness connector F15 (A) ter-
minal 20 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
.
>> Inspection End.
IPDM E/R
Ground
Condition
Voltage (V)
Connector Terminal
E18
30
Ground
CVT selector
lever
P or N
Battery voltage
Other than
above
0
ALKIA1308ZZ
TCM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
A: F15
20
B: E18
72
Yes
TCM
Ground
Continuity
Connector
Terminal
A: F15
20
Ground
No
ALKIA1309ZZ
SEC-78
< DTC/CIRCUIT DIAGNOSIS >
B2110 TRANSMISSION RANGE SWITCH
B2110 TRANSMISSION RANGE SWITCH
Description
INFOID:0000000010052002
IPDM E/R confirms the shift position with the following signals.
• Transmission range switch
• Shift position signal from BCM (CAN)
DTC Logic
INFOID:0000000010052003
DTC DETECTION LOGIC
NOTE:
• If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2110 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON under the following conditions and wait for at least 1 second.
-
CVT selector lever is in the P or N position
-
Do not depress the brake pedal
2. Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000010052004
Regarding Wiring Diagram information, refer to
.
1.
CHECK DTC WITH BCM
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK TRANSMISSION RANGE SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Turn ignition switch ON.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2110
TRANSMISSION
RANGE SWITCH
IPDM E/R detects mismatch between the signal
below for 1 second or more.
• Transmission range switch input signal
• Harness or connectors
Transmission range switch circuit is
open or shorted
• Transmission range switch
B2110 TRANSMISSION RANGE SWITCH
SEC-79
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
4. Check voltage between IPDM E/R harness connector E18 termi-
nal 30 and ground under following condition.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-35, "Removal and Installation"
.
NO
>> GO TO 3.
3.
CHECK TRANSMISSION RANGE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check continuity between IPDM E/R harness connector E18 (B)
terminal 72 and TCM harness connector F15 (A) terminal 20.
4. Check continuity between TCM harness connector F15 (A) ter-
minal 20 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
.
>> Inspection End.
ALKIA1308ZZ
IPDM E/R
Ground
Condition
Voltage (V)
Connector
Terminal
E18
30
Ground
CVT selector lever
P or N
Battery voltage
Other than above
0
TCM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
A: F15
20
B: E18
72
Yes
TCM
Ground
Continuity
Connector
Terminal
A: F15
20
Ground
No
ALKIA1309ZZ
SEC-80
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
BCM
BCM : Diagnosis Procedure
INFOID:0000000010068741
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSE AND FUSIBLE LINK
Check if the following BCM fuses or fusible link are blown.
Is the fuse or fusible link blown?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit.
NO
>> GO TO 2
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Is the measurement normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Inspection End.
NO
>> Repair or replace harness.
BCM : Special Repair Requirement
INFOID:0000000010068742
1.
REQUIRED WORK WHEN REPLACING BCM
Initialize control unit. Refer to
BCS-5, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) :
Terminal No.
Signal name
Fuse and fusible link No.
1
Battery power supply
H
11
10
24
7
Terminals
Voltage
(Approx.)
(+)
(
−)
BCM
Ground
Connector
Terminal
M16
1
Battery voltage
M17
11
M18
24
BCM
Ground
Continuity
Connector
Terminal
M17
13
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст