Nissan Maxima. Manual — part 1122
STEERING GEAR AND LINKAGE
ST-33
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000009465787
Disassembly
INFOID:0000000009465788
1. Remove outer socket locknut and outer socket.
2. Remove boot clamps and boot.
CAUTION:
Do not reuse boot clamps.
3. Remove inner socket.
Inspection
INFOID:0000000009465789
INSPECTION AFTER DISASSEMBLY
Boot
Check boot for cracks. Replace if any damage is found.
Outer Socket and Inner Socket
• Ball joint swinging torque
1.
Outer socket
2.
Boot clamp
3.
Boot
4.
Inner socket
5.
Boot clamp
6.
SSPS valve (part of gear assembly)
7.
Gear assembly
Front
Three Bond 1111B or equivalent
AWGIA0101GB
ST-34
< UNIT DISASSEMBLY AND ASSEMBLY >
STEERING GEAR AND LINKAGE
- Hook a spring balance to the ball stud and inner socket measuring
point (*) and pull the spring balance. Make sure that the spring bal-
ance reads the specified value when ball stud and inner socket
start to move. Replace outer socket and steering gear assembly if
they are outside the standard.
• Ball joint rotating torque
- Make sure that the reading is within the following specified range
using Tool. Replace outer socket if the reading is outside the spec-
ified value.
• Ball joint axial end play
- Apply an axial load of 490 N (50 kg, 111 lb) to ball stud. Measure
amount of stud movement using a dial gauge and then make sure
that the value is within the following specified range. Replace outer
socket and inner socket if the measured value is outside the stan-
dard.
Assembly
INFOID:0000000009465790
1. Apply Three Bond 1111B or equivalent to inner socket and turn pinion fully to retract inner socket into gear
housing assembly.
2. Install large end (1) of boot (2) to gear housing assembly.
3. Install small end (3) of boot (2) to inner socket boot mounting
groove.
Tool number
: — (J-44372)
Swinging torque
: Refer to
SGIA0896E
Tool number
: ST3127S000 (J-25765-A)
Rotating torque
: Refer to
SGIA0941E
Axial end play
: Refer to
SGIA0057E
AWGIA0107ZZ
STEERING GEAR AND LINKAGE
ST-35
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
4. Install boot clamp to boot small end.
CAUTION:
Do not reuse boot clamps.
5. Install boot clamp to boot large end using Tool.
CAUTION:
Do not reuse boot clamps.
6. Adjust inner socket to standard length (L), and then tighten lock
nut to the specified torque. Check length of inner socket (L)
again after tightening lock nut. Make sure that the length is the
standard.
CAUTION:
Adjust toe-in after this procedure. The length achieved after
toe-in adjustment is not necessarily the above value.
Tool number
: KV40107300 ( — )
AST139
Inner socket length (L)
: Refer to
SGIA0167E
ST-36
< UNIT DISASSEMBLY AND ASSEMBLY >
POWER STEERING OIL PUMP
POWER STEERING OIL PUMP
Disassembly and Assembly
INFOID:0000000009465791
The power steering oil pump and pulley is not serviceable and should be replaced as an assembly. For front
and rear bracket removal, refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст