Nissan Leaf. Manual — part 571
EVC-308
< DTC/CIRCUIT DIAGNOSIS >
P31B8 EV SYSTEM CAN COMMUNICATION
P31B8 EV SYSTEM CAN COMMUNICATION
DTC Logic
INFOID:0000000010120777
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
• Turn power switch OFF and wait at least 90 seconds.
CAUTION:
During this period, never perform vehicle handling such as opening and closing of doors. If some
kind of vehicle handling is performed, then wait another 90 seconds or more from the time of the
vehicle handling.
• Make sure that 12V battery voltage is 11 V or more.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn power switch ON and wait at least 10 seconds.
2. Check DTC.
Is DTC detected?
YES
>> Proceed to
EVC-308, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010120778
1.
CHECK TCU CONDITION
Check that the TCU activation is performed normally. Refer to
AV-575, "ADDITIONAL SERVICE WHEN
USING TELEMATICS SYSTEM FOR THE FIRST TIME/RE-SUBSCRIPTION : Description"
Is TCU activation performed normally?
YES
>> GO TO 2.
NO
>> Perform TCU activation. Refer to
AV-575, "ADDITIONAL SERVICE WHEN USING TELEMATICS
SYSTEM FOR THE FIRST TIME/RE-SUBSCRIPTION : Work Procedure"
.
2.
PERFORM TROUBLE DIAGNOSIS FOR CAN COMMUNICATION
Perform trouble diagnosis for CAN communication. Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK SELF-DIAGNOSTIC RESULT IN VCM
With CONSULT
Check self-diagnostic result in “EV/HEV”.
Is any EV system CAN error (U1000 excluded) other than DTC P31B8 detected?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
REPLACE VCM
With CONSULT
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P31B8
COMMUNICATION ERROR
(Communication error)
When VCM detects an error signal that is received from TCU via
CAN communication
• CAN communication
• TCU
• VCM
P31B8 EV SYSTEM CAN COMMUNICATION
EVC-309
< DTC/CIRCUIT DIAGNOSIS >
D
E
F
G
H
I
J
K
L
M
A
B
EVC
N
O
P
1. Replace VCM. Refer to
EVC-423, "Removal and Installation"
.
2. Perform DTC confirmation procedure again. Refer to
Is DTC P31B8 detected again?
YES
>> Replace TCU. Refer to
AV-594, "Removal and Installation"
.
NO
>> INSPECTION END
5.
REPLACE TCU
With CONSULT
1. Replace TCU. Refer to
AV-594, "Removal and Installation"
2. Perform DTC confirmation procedure again. Refer to
Is DTC P31B8 detected again?
YES
>> Replace VCM. Refer to
EVC-423, "Removal and Installation"
.
NO
>> INSPECTION END
EVC-310
< DTC/CIRCUIT DIAGNOSIS >
P31BA CAN COMMUNICATION
P31BA CAN COMMUNICATION
DTC Logic
INFOID:0000000010120779
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
• Turn power switch OFF and wait at least 90 seconds.
CAUTION:
During this period, never perform vehicle handling such as opening and closing of doors. If some
kind of vehicle handling is performed, then wait another 90 seconds or more from the time of the
vehicle handling.
• Make sure that 12V battery voltage is 11 V or more.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Turn power switch ON and wait at least 10 seconds.
2. Check DTC.
Is DTC detected?
YES
>> Proceed to
EVC-310, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010120780
1.
PERFORM TROUBLE DIAGNOSIS FOR CAN COMMUNICATION
Perform trouble diagnosis for CAN communication. Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK SELF-DIAGNOSTIC RESULT IN VCM
With CONSULT
Check self-diagnostic result in “EV/HEV”.
Is any CAN error (U1000 excluded) other than DTC P31BA detected?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
REPLACE VCM
With CONSULT
1. Replace VCM. Refer to
EVC-423, "Removal and Installation"
.
2. Perform DTC confirmation procedure again. Refer to
Is DTC P31BA detected again?
YES
>> Replace BCM. Refer to
BCS-72, "Removal and Installation"
NO
>> INSPECTION END
4.
REPLACE BCM
With CONSULT
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P31BA
COMMUNICATION ER-
ROR
(Communication error)
When VCM detects an error signal that is received from BCM via
CAN communication
• CAN communication
• BCM
• VCM
P31BA CAN COMMUNICATION
EVC-311
< DTC/CIRCUIT DIAGNOSIS >
D
E
F
G
H
I
J
K
L
M
A
B
EVC
N
O
P
1. Replace BCM. Refer to
BCS-72, "Removal and Installation"
.
2. Perform DTC confirmation procedure again. Refer to
Is DTC P31BA detected again?
YES
>> Replace VCM. Refer to
EVC-423, "Removal and Installation"
.
NO
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст