Nissan Leaf. Manual — part 960
MWI
SYSTEM
MWI-43
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Other 1, Other 2, Other 3 (Maintenance)
• When all the following operating conditions are satisfied, the combination meter displays an other warning
on the information display by an interrupt:
• The combination meter judges showing/hiding of “other warning”, according to the signals below:
Meter Illumination Level Indication
When receiving the following signals, the combination meter causes an interrupt on the information display to
indicate an illumination level:
TIMER STATUS REMINDER DISPLAY
• The combination meter receives the next charge time signal, next departure time signal or next pre-A/C time
signal when the power switch is READY and displays the timer charging after the power switch is turned
OFF.
• Pressing the
switch (enter switch) changes the displayed item in the following sequence:
Timer charging ON/OFF, timer A/C ON/OFF
→ Next charge start time / end time → Charging time → Timer
A/C start time
• If no switches are operated for 10 seconds, the display screen turns OFF.
• The combination meter judges showing/hiding of the “timer status reminder display” according to the signals
below.
WARNING CHECK INDICATION
• The combination meter can cause an interrupt on the information display to indicate a warning, based on
signals received from each unit and switch.
• The indicated warning can be checked with “WARNING” during the satisfaction of an interrupt indication
condition for each warning.
Warning Display Items
• Door open warning
• Electric shift warning
• Power limitation warning
Signal name
Signal path
Power switch ON signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination
meter
Operating condition
Power switch
ON
Mileage
More than value set in “SETTING”
Signal name
Signal path
Power switch ON signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination
meter
Signal name
Signal path
Power switch ON signal
—
Illumination control switch signal
Meter control switch
Combination meter
Signal name
Signal path
Next charge time signal
VCM
Combination
meter
Next departure time signal
Next pre-A/C time signal
MWI-44
< SYSTEM DESCRIPTION >
SYSTEM
• Li-ion battery low charge warning
• Take away warning (push start display)
• Intelligent Key system warning
SETTING
Warning indication timing and time can be set.
Target Amount of Charge (Without Navigation)
Allows the user to set the target amount of charge at 100 % or 80 % of full charge.
Timer charge (Without Navigation)
The settings of timer charge ON/OFF and stop time can be adjusted arbitrarily.
NOTE:
• For further information about timer charge, refer to
MWI-30, "TIMER CHARGE AND A/C-HEATER TIMER
(CLIMATE CTRL. TIMER) (WITHOUT NAVIGATION) : System Description"
.
• For models with navigation system, settings can be performed on the AV control unit display. When the AV
control unit is removed, the settings screen of timer charge may be displayed on the information display.
A/C-heater timer (Climate Ctrl. Timer) (Without Navigation)
The settings of A/C-heater timer (Climate Ctrl. Timer) ON/OFF and estimated time of departure can be
adjusted arbitrarily.
NOTE:
• For further information about A/C-heater timer (Climate Ctrl. Timer), refer to
AND A/C-HEATER TIMER (CLIMATE CTRL. TIMER) (WITHOUT NAVIGATION) : System Description"
.
• For models with navigation system, settings can be performed on the AV control unit display. When the AV
control unit is removed, the settings screen of A/C-heater timer (Climate Ctrl. Timer) may be displayed on
the information display.
Clock
Setting values for “Set clock”, and “24/12 Hr” can be adjusted to meet the user's needs.
Maintenance
Setting values for tire and other maintenance items can be adjusted to meet the user's needs.
Setting Item
Target amount
of charge
80%, 100%
Setting Item
Timer charge
The settings of ON/OFF and stop time can be ad-
justed arbitrarily.
Setting Item
A/C-heater timer
(Climate Ctrl. Timer)
The settings of ON/OFF and estimated time of de-
parture can be adjusted arbitrarily.
Setting item
Set clock
Adjusting the time
24/12 Hr
12 h, 24h
MWI
SYSTEM
MWI-45
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Alarms
Setting values for “Driver Alert”, and “Outside Temp” can be adjusted to meet the user's needs.
Units
Setting values for “TEMPERATURE” and “SPEED” items can be adjusted to meet the user's needs.
Language
Setting values for “Language” items can be adjusted to meet the user's needs.
Effects
Setting values for “Effects” items can be adjusted to meet the user's needs.
For the effects function, refer to
VSP-13, "START UP SOUND SYSTEM : System Description"
Factory
Allows the user to reset all settings other than the odometer.
Settings-reject Indication
• Regarding settings-reject indications, “SETTING CAN BE OPERATED WHEN STOPPED” is shown on the
information display when indication conditions are satisfied.
• When reaching 3.1 MPH (5 km/h) after accelerating from a stopping condition, a settings-reject indication is
displayed.
• When reaching less than 0.6 MPH (1 km/h) after decelerating from 3.1 MPH (5 km/h), a settings-reject indi-
cation is cancelled to allow settings.
Setting item
Setting range
Maintenance
Tire
No setting, 250 mile - 18,500 mile
(No setting, 500 km - 30,000 km)
Other 1
No setting, 250 mile - 18,500 mile
(No setting, 500 km - 30,000 km)
Other 2
No setting, 250 mile - 18,500 mile
(No setting, 500 km - 30,000 km)
Other 3
No setting, 250 mile - 18,500 mile
(No setting, 500 km - 30,000 km)
Setting item
Setting range
Setting unit
Alarms
Drive Alert
No setting, 0.5 h - 6 h
0.5 h
Outside Temp
ON/OFF
—
Setting item
TEMPERA-
TURE
Deg F
Deg C
SPEED
MPH, mile/kWh
km/h, km/kWh
Setting item
Language
English
Francais
Espanol
Setting item
Effects
Sound 1
Sound 2
Sound 3
OFF
MWI-46
< SYSTEM DESCRIPTION >
SYSTEM
• The combination meter judges a vehicle condition based on the following signals and displays a settings-
reject indication on the information display:
TIMING CHART
ODO/TRIP METER
The combination meter calculates mileage, based on the following signals and displays the mileage on the
information display:
SHIFT INDICATOR
The combination meter displays the shift position based on the signals below.
Signal name
Signal path
Power switch ON signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
AWNIA3461GB
Signal name
Signal path
Power switch ON signal
—
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Signal name
Signal path
Power switch ON signal
—
Shift position signal
VCM
Combination
meter
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст