Nissan Leaf. Manual — part 1288

C1729 VEHICLE SPEED SIGNAL

WT-31

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1729 VEHICLE SPEED SIGNAL

DTC Logic

INFOID:0000000010120195

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC CONFIRMATION PROCEDURE

With CONSULT

1. Drive the vehicle.

2. Stop the vehicle.

3. Perform “Self Diagnostic Result“” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?

YES

>> Proceed to

WT-31, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000010120196

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF DIAGNOSTIC RESULT

With CONSULT

Perform “Self Diagnostic Result””“ for “ABS”.
Are any DTCs detected?

YES

>> Refer to

BRC-56, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK BCM INPUT/OUTPUT SIGNAL

Check the BCM input/output signal values. Refer to

BCS-28, "Reference Value"

.

Is the inspection result normal?

YES

>> Check pin terminal and connection of each harness connector for malfunctioning conditions.

NO

>> Replace the BCM. Refer to

BCS-72, "Removal and Installation"

.

DTC

Display Item

Malfunction detected condition

Possible causes

C1729

VHCL SPEED SIG ERR

Vehicle speed signal not detected.

• CAN communication
• BCM
• ABS actuator and electric unit (control unit) mal-

function

WT-32

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000010120197

Regarding Wiring Diagram information, refer to

WT-15, "Wiring Diagram"

.

1.

CHECK FUSE AND FUSIBLE LINK

Check that the following fuse and fusible link are not blown:

Is the fuse or fusible link blown?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1. Disconnect BCM connector M25.

2. Check voltage between BCM connector M25 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

CHECK GROUND CIRCUIT

Check continuity between BCM connector M25 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

Terminal No.

Signal name

Fuse and fusible link No.

57

Battery power supply

9 (10A)

70

H (40A)

BCM

Ground

Voltage

(Approx.)

Connector

Terminal

M25

57

—

Battery voltage

70

BCM

Ground

Continuity

Connector

Terminal

M25

67

—

Yes

TPMS

WT-33

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

SYMPTOM DIAGNOSIS

TPMS

Symptom Table

INFOID:0000000010120198

LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART

WT-34

< SYMPTOM DIAGNOSIS >

TPMS

Diagnosis

items

Symptom

(Power switch ON)

Low tire pressure warning lamp

Cause

Action

Low tire pres-
sure warning
lamp

The low tire pres-
sure warning lamp
illuminates for 1
second, then turns
OFF.

Wake-up operation for
all tire pressure sensors
at wheels is completed.

No system malfunctions.

The low tire pres-
sure warning lamp
repeats blinking
ON for 2 seconds
and OFF for 0.2
seconds.

Wake-up operation for
all tire pressure sensors
at wheels is not complet-
ed.

Perform the ID registration
for all tire pressure sensors
at wheels. Refer to

WT-21,

"Work Procedure"

.

The low tire pres-
sure warning lamp
blinks once.

The front left tire pres-
sure sensor is not acti-
vated.

Perform the ID registration
for the tire pressure sensor
at front left wheel. Refer to

WT-21, "Work Procedure"

.

The low tire pres-
sure warning lamp
repeats blinking
twice.

The front right tire pres-
sure sensor is not acti-
vated.

Perform the ID registration
for the tire pressure sensor
at front right wheel. Refer
to

WT-21, "Work Proce-

dure"

.

The low tire pres-
sure warning lamp
repeats blinking
for 3 times.

The rear right tire pres-
sure sensor is not acti-
vated.

Perform the ID registration
for the tire pressure sensor
at rear right wheel. Refer to

WT-21, "Work Procedure"

.

The low tire pres-
sure warning lamp
repeats blinking
for 4 times.

The rear left tire pres-
sure sensor is not acti-
vated.

Perform the ID registration
for the tire pressure sensor
at rear left wheel. Refer to

WT-21, "Work Procedure"

.

The low tire pres-
sure warning lamp
turns ON and
stays illuminated.

Low tire pressure.

Check the tire pressure for
all wheels and adjust to the
specified value. Refer to

WT-51, "Tire Air Pressure"

.

SEIA0592E

SEIA0593E

JPEIC0090GB

SEIA0595E

SEIA0596E

SEIA0597E

SEIA0598E