Nissan Leaf. Manual — part 1057
FRONT SEAT
SE-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
8. Unclip the side air bag module harness from the seat frame assembly and route the harness through the
seat cushion trim.
NOTE:
Take note of harness routing and attachment location for correct installation.
9. Disconnect the seat cushion harness connector and unclip it from the seat frame assembly.
NOTE:
Take note of harness routing and attachment location for correct installation.
10. Release J-clip retainers (A) from the seat frame assembly.
11. Remove the seat cushion from the seat frame assembly.
ASSEMBLY
Assembly is in the reverse order of disassembly.
CAUTION:
• Smooth out all wrinkles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the self diagnosis using the air bag warning lamp or CONSULT. Refer to
or
JMJIA8334ZZ
SE-36
< REMOVAL AND INSTALLATION >
REAR SEAT
REAR SEAT
Exploded View
INFOID:0000000010122963
SEATBACK
1.
Seatback latch release knob
2.
Seat latch release knob finisher 3.
Seatback latch finisher (RH)
4.
Seatback striker (RH)
5.
Seatback support (RH)
6.
Seatback hinge bracket finisher (RH)
7.
Seatback latch assembly (RH) 8.
Seatback trim (RH)
9.
Seatback pad (RH)
10. Seatback hinge bracket (RH)
11. Seatback assembly (RH)
12. Seatback hinge bracket (center)
13. Seat cushion trim
14. Seat cushion hook
15. Seatback pad (LH)
16. Seatback trim (LH)
17. Seat cushion assembly
18. Seatback support (LH)
19. Seatback frame (LH)
20. Seatback hinge bracket (LH)
21. Seatback hinge bracket finisher (LH)
22. Seatback latch assembly (LH)
23. Seatback latch finisher (LH)
24. Seatback striker (LH)
25. Headrest holder (locked)
26. Headrest holder (free)
27. Center seat belt cover
28. Seatback assembly (LH)
29. Headrest (LH)
30. Center seat belt finisher
31. Center seat belt retractor
32. Seatback frame (RH)
33. Headrest (RH)
AWJIA1054ZZ
REAR SEAT
SE-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
SEATBACK : Removal and Installation
INFOID:0000000010122964
REMOVAL
Seatback Assembly (LH)
1. Remove the seat cushion assembly. Refer to
SE-40, "SEAT CUSHION : Removal and Installation"
.
2. Remove center anchor bolt of center seat belt retractor. Refer to
3. Place the rear seatback assembly (LH) in the folded down position.
4. Pull up seatback trim, then remove bolts from the seatback hinge bracket (center).
5. Remove the luggage finisher mask (LH). Refer to
INT-42, "LUGGAGE FINISHER MASK : Removal and
.
6. Remove nuts from the seatback hinge bracket (LH).
7. Remove seatback assembly (LH) from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
Seatback Assembly (RH)
1. Remove the seat cushion assembly. Refer to
SE-40, "SEAT CUSHION : Removal and Installation"
.
2. Place the seatback assembly (RH) in the folded down position.
3. Pull up seatback trim, then remove bolts from the seatback hinge bracket (center).
4. Remove the luggage finisher mask (RH). Refer to
INT-42, "LUGGAGE FINISHER MASK : Removal and
.
5. Remove nuts from the seatback hinge bracket (RH).
6. Remove seatback assembly (RH) from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
Installation is in the reverse order of removal.
• Temporary install bolts, position seatback assembly (LH/RH) to the latched position. Check that seatback
latch assembly and seatback striker do not interfere, then tighten bolts to specification. Refer to
• Tighten the center anchor bolt to specification. Refer to
.
SEATBACK : Disassembly and Assembly
INFOID:0000000010122965
DISASSEMBLY
1. Remove seatback hinge bracket (LH/RH). Refer to
SE-41, "SEATBACK HINGE : Removal and Installa-
2. Release J-clip retainer (A) and then unzip seatback zippers (B).
• Seatback assembly (LH)
JMJIA8708ZZ
SE-38
< REMOVAL AND INSTALLATION >
REAR SEAT
• Seatback assembly (RH)
3. Remove seatback support.
Release the seatback support from seatback frame at locations
(A) and remove the seatback support.
• Seatback assembly (LH)
• Seatback assembly (RH)
4. Pull out seatback trim from ISO FIX at locations (A).
• Seatback assembly (LH)
JMJIA8709ZZ
JMJIA8356ZZ
JMJIA8357ZZ
JMJIA8358ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст