Nissan Leaf. Manual — part 1099
LAP PRE-TENSIONER
SR-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
LAP PRE-TENSIONER
Exploded View
INFOID:0000000010120272
.
Removal and Installation
INFOID:0000000010120273
For removal and installation procedures, refer to
SB-11, "SEAT BELT RETRACTOR : Removal and Installa-
.
SR-42
< REMOVAL AND INSTALLATION >
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
Removal and Installation
INFOID:0000000010502828
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Do not use air tools or electric tools for servicing.
Removal
1. Remove front passenger seat assembly. Refer to
SE-29, "Removal and Installation"
2. Remove occupant classification system control unit bolts.
3. Disconnect the harness connector from the occupant classification system control unit.
4. Remove occupant classification system control unit.
CAUTION:
• Replace the occupant classification control unit if it has been dropped or sustained an impact.
• Do not strike the occupant classification control unit.
Installation
Installation is in the reverse order of removal.
CAUTION:
• Do not damage the harness connector during installation.
• After installation is complete, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is indicated by the air bag warning lamp after repair or replacement of the malfunc-
tioning parts, perform the SRS final check. Refer to
SRC-37, "ADDITIONAL SERVICE WHEN
REPLACING CONTROL UNIT : Description"
.
OCCUPANT CLASSIFICATION SYSTEM SENSORS
WARNING:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
• Do not use air tools or electric tools for servicing.
Removal
1. Remove front passenger seat cushion. Refer to
SE-29, "Removal and Installation"
.
2. Remove seat cushion pan bolts then lift seat cushion pan and disconnect harness connectors from occu-
pant classification sensors.
3. Remove nuts and washer then remove seat frame from the seat track.
4. Remove nuts from occupant classification sensor and remove.
Installation
1. Install occupant classification sensor to seat track using nuts.
CAUTION:
Do not reuse nuts.
2. Install seat frame to seat track using nuts and washer.
CAUTION:
Do not reuse nuts or washer.
NOTE:
Tighten all nuts by hand first, first tighten front (LH) nut, then tighten rear (LH) nut. Tighten all remaining
nuts.
Occupant classification
sensor nuts
:22 N·m (2.2 kg-m, 16 ft-lb)
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
SR-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
3. Connect harness connectors to occupant classification sensors then install seat cushion pan using bolts.
CAUTION:
Do not reuse bolts.
4. Install front passenger seat cushion. Refer to
SE-29, "Removal and Installation"
Seat track (LH) nuts
:45 N·m (4.6 kg-m, 33 ft-lb)
Seat track (RH) nuts
:22 N·m (2.2 kg-m, 16 ft-lb)
Seat cushion pan bolts
:22 N·m (2.2 kg-m, 16 ft-lb)
SR-44
< REMOVAL AND INSTALLATION >
PASSENGER AIR BAG INDICATOR
PASSENGER AIR BAG INDICATOR
Removal and Installation
INFOID:0000000010120276
Removal
1. Remove cluster lid C. Refer to
IP-17, "Removal and Installation"
2. Remove screws (A) then the passenger air bag indicator (1)
from cluster lid C (2).
Installation
Installation is in the reverse order of removal.
ALHIA0302ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст