Nissan Leaf. Manual — part 558
EVC-256
< DTC/CIRCUIT DIAGNOSIS >
P316C, P316D, P316E PDM (POWER DELIVERY MODULE)
P316C, P316D, P316E PDM (POWER DELIVERY MODULE)
DTC Logic
INFOID:0000000010120715
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
INSPECTION START
NOTE:
This DTC is displayed when PDM (Power Delivery Module) detects a DTC. If the DTC is displayed, perform
trouble diagnosis for a DTC that detected by PDM (Power Delivery Module).
>> Proceed to
EVC-256, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010120716
Perform the self-diagnosis of PDM (Power Delivery Module).
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P316C
PD MODULE SYSTEM
(Power Delivery Module
system)
VCM receives a DTC detection signal sent from PDM (Pow-
er Delivery Module).
PDM (Power Delivery Mod-
ule)
P316D
P316E
P316F PDM (POWER DELIVERY MODULE)
EVC-257
< DTC/CIRCUIT DIAGNOSIS >
D
E
F
G
H
I
J
K
L
M
A
B
EVC
N
O
P
P316F PDM (POWER DELIVERY MODULE)
DTC Logic
INFOID:0000000010120717
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
• Turn power switch OFF and wait at least 90 seconds.
CAUTION:
During this period, never perform vehicle handling such as opening and closing of doors. If some
kind of vehicle handling is performed, then wait another 90 seconds or more from the time of the
vehicle handling.
• Make sure that 12V battery voltage is 11 V or more.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE-1
1. Perform normal charging and wait at least 10 minutes.
2. Turn power switch ON.
3. Check DTC.
Is DTC detected?
YES
>> Proceed to
EVC-257, "Diagnosis Procedure"
NO (Without quick charge port)>>INSPECTION END
NO (With quick charge port)>>GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE-2
1. Turn power switch OFF.
2. Perform quick charging and wait at least 10 minutes.
3. Turn power switch ON.
4. Check DTC.
Is DTC detected?
YES
>> Proceed to
EVC-257, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010120718
1.
CHECK PDM (POWER DELIVERY MODULE) OUTPUT POWER-1
With CONSULT
1. Turn power switch OFF.
2. Perform normal charging.
3. Turn power switch ON.
4. On the CONSULT screen, select “EV/HEV” >> “DATA MONITOR” >> “OBC OUT PWR”.
Is value 0kW?
YES
>> GO TO 3.
NO-1 (with quick charge port)>>GO TO 2.
NO-2 (without quick charge port)>>Replace VCM. Refer to
EVC-423, "Removal and Installation"
2.
CHECK PDM (POWER DELIVERY MODULE) OUTPUT POWER-2
With CONSULT
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P316F
PD MODULE SYSTEM
(Power delivery Module
system)
The charge electricity of the PDM (Power Delivery Module) is less
than 0.1KW
• Harness or connector
• PDM (Power Delivery
Module)
• VCM
EVC-258
< DTC/CIRCUIT DIAGNOSIS >
P316F PDM (POWER DELIVERY MODULE)
1. Turn power switch OFF.
2. Perform quick charging.
3. Turn power switch ON.
4. On the CONSULT screen, select “EV/HEV” >> “DATA MONITOR” >> “OBC OUT PWR”.
Is value 0 kW?
YES
>> INSPECTION END (quick charger malfunction)
NO
>> Replace VCM. Refer to
EVC-423, "Removal and Installation"
.
3.
PERFORM SELF-DIAGNOSIS OF PDM (POWER DELIVERY MODULE)
Perform self-diagnosis of PDM (Power Delivery Module).
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> Check to see if there is a factor causing a situation that battery charge does not start. Refer to
P3170, P3171 PDM (POWER DELIVERY MODULE)
EVC-259
< DTC/CIRCUIT DIAGNOSIS >
D
E
F
G
H
I
J
K
L
M
A
B
EVC
N
O
P
P3170, P3171 PDM (POWER DELIVERY MODULE)
DTC Logic
INFOID:0000000010120719
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
INSPECTION START
NOTE:
This DTC is displayed when PDM (Power Delivery Module) detects a DTC. If the DTC is displayed, perform
trouble diagnosis for a DTC that detected by PDM (Power Delivery Module).
>> Proceed to
EVC-259, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010120720
Perform the self-diagnosis of PDM (Power Delivery Module).
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P3170
PD MODULE SYSTEM
(Power Delivery module
system)
VCM receives a DTC detection signal sent from PDM (Pow-
er Delivery Module).
PDM (Power Delivery Mod-
ule)
P3171
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст