Nissan Leaf. Manual — part 426
REAR DOOR LOCK
DLK-199
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
8. Slide outside handle bracket toward rear of vehicle to remove.
: Front
9. Disconnect outside handle cable (1) from outside handle bracket
(2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check door open/close and lock/unlock operation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA6416ZZ
JMKIA6417ZZ
DLK-200
< REMOVAL AND INSTALLATION >
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000010119901
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000010119902
REMOVAL
1. Remove the back door lower finisher. Refer to
INT-48, "BACK DOOR LOWER FINISHER : Removal and
.
2. Remove back door lock harness (1) from back door lock assem-
bly (2).
3. Disconnect the harness connector (A) from the back door lock
assembly.
4. Remove back door lock assembly bolts and back door lock assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check back door open/close and lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010119903
REMOVAL
1. Remove the back door lower finisher. Refer to
INT-48, "BACK DOOR LOWER FINISHER : Removal and
.
1.
Back door lock assembly
2.
Bolt
3.
Back door striker
4.
Outside handle
Do not reuse
Grease
AWKIA2413ZZ
JMKIA6410ZZ
BACK DOOR LOCK
DLK-201
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Disconnect the harness connectors from the outside handle and
rear view camera (if equipped).
3. Remove outside handle nuts.
4. Remove harness grommet from back door panel, then remove the outside handle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check back door open/close and lock/unlock operation.
JMKIA6508ZZ
DLK-202
< REMOVAL AND INSTALLATION >
KEY CYLINDER
KEY CYLINDER
GLOVE BOX LID KEY CYLINDER
GLOVE BOX LID KEY CYLINDER : Removal and Installation
INFOID:0000000010436591
REMOVAL
1. Insert key (1) into glove box lid lock cylinder (2).
2. Pull upward on glove box lid release handle (3).
3. Rotate key (1) and turn glove box lid key cylinder (2) to the lock
position.
4. Press tumbler stopper (1) into glove box lid lock cylinder (2)
using a suitable tool (A), and then remove key (3) and glove box
lid lock cylinder together from glove box lid release handle (4).
NOTE:
When removing glove box lid lock cylinder (2) note the position
of cylinder to glove box lid release handle (4).
5. Remove sleeve (3) from glove box lid release handle and then
install sleeve to glove box lid lock cylinder.
NOTE:
When removing sleeve note the position of sleeve to glove box
lid release handle.
CAUTION:
Do not pull out key (1) from glove box lid lock cylinder (2)
while sleeve (3) is removed. Otherwise, tumblers (4) may be
lost from glove box lid lock cylinder.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check glove box assembly open/close, lock/unlock operation.
JMKIA5490ZZ
JMKIA5491ZZ
JMKIA5819ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст