Nissan Leaf. Manual — part 298
BRAKE POWER SUPPLY BACKUP UNIT
BR-513
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE POWER SUPPLY BACKUP UNIT
Exploded View
INFOID:0000000010123141
Removal and Installation
INFOID:0000000010123142
REMOVAL
1. Turn the power switch OFF to exit CONSULT.
2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle and CONSULT while waiting.
3. Remove luggage side lower finisher LH. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER :
.
4. Disconnect brake power supply backup unit harness connector.
5. Remove brake power supply backup unit and bracket.
CAUTION:
To prevent damage to the parts, never drop removed parts.
6. Remove bracket from brake power supply backup unit.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Align the direction of mark located on the back of brake power
supply backup unit with that of mark on bracket .
Brake power supply backup unit
Bracket
: N·m (kg-m, in-lb)
JSFIA1668GB
JSFIA1669ZZ
BR-514
< REMOVAL AND INSTALLATION >
BRAKE POWER SUPPLY BACKUP UNIT
• To install bracket to brake power supply backup unit , securely
insert the bracket until protrusion of the brake power supply unit
protrudes from lock hole of the bracket.
JSFIA1670ZZ
WARNING BUZZER
BR-515
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
WARNING BUZZER
Removal and Installation
INFOID:0000000010123143
REMOVAL
1. Remove glove box cover assembly. Refer to
IP-17, "Removal and Installation"
.
2. Disconnect warning buzzer harness connector.
3. Remove warning buzzer.
INSTALLATION
Install in the reverse order of removal.
BR-516
< REMOVAL AND INSTALLATION >
FRONT DISC BRAKE
FRONT DISC BRAKE
BRAKE PAD
BRAKE PAD : Exploded View
INFOID:0000000010123144
BRAKE PAD : Removal and Installation
INFOID:0000000010123145
WARNING:
Clean dust on brake calipers and brake pads with a vacuum dust collector to minimize the hazard of
airborne particles or other materials.
CAUTION:
• While removing brake caliper, do not depress brake pedal because piston will pop out.
• It is not necessary to remove bolts from torque member and brake hose except for disassembly or
replacement of brake caliper assembly. In this case, hang brake caliper with a wire so as not to
stretch brake hose.
• Do not damage piston boot.
• Keep brake rotor and brake pads free from brake fluid and grease.
• Burnish the brake pads and disc brake rotor mutually contacting surfaces after refinishing or replac-
ing disc brake rotors, after replacing brake pads, or if a soft pedal occurs at very low mileage. Refer
BR-496, "BRAKE PAD : Inspection and Adjustment"
REMOVAL
1. Partially drain brake fluid from the master cylinder. Refer to
.
2. Remove the front wheel and tire using power tool. Refer to
WT-45, "Removal and Installation"
1.
Inner shim cover
2.
Inner shim
3.
Inner pad
4.
Outer pad
5.
Pad retainer upper
6.
Outer shim
7.
Outer shim cover
8.
Pad retainer lower
A.
Molykote AS-880N grease
B.
Molykote 7439 grease
NOTE:
LH shown, RH similar
AWFIA1012ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст