Nissan Leaf. Manual — part 1295
WW-8
< SYSTEM DESCRIPTION >
SYSTEM
SYSTEM
FRONT WIPER AND WASHER SYSTEM
FRONT WIPER AND WASHER SYSTEM : System Description
INFOID:0000000010122199
SYSTEM DIAGRAM
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Front wiper control function
Control by IPDM E/R
• Front wiper control function
• Relay control function
Combination meter indicates low washer fluid warning judged by the signal from the washer fluid level switch.
For details of low washer fluid warning, refer to
MWI-35, "INFORMATION DISPLAY : System Description"
.
FRONT WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R via CAN communication depending on each oper-
ating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper HI/LO relay according to the
front wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LO) to IPDM E/R via CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Power switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HI) to IPDM E/R via CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Power switch ON
- Front wiper switch HI
• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
FRONT WIPER INT OPERATION
AWLIA2357GB
SYSTEM
WW-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
• BCM transmits the front wiper request signal (INT) to IPDM E/R via CAN communication depending on the
front wiper INT operating condition and intermittent operation delay interval according to the wiper intermit-
tent dial position.
Front wiper INT operating condition
- Power switch ON
- Front wiper switch INT
• IPDM E/R turns ON the integrated front wiper relay so that the front wiper is operated only once according to
the front wiper request signal (INT).
• BCM detects stop position/except stop position of the front wiper motor according to the front wiper stop
position signal received from IPDM E/R via CAN communication.
• BCM transmits the front wiper request signal (INT) again after the intermittent operation delay interval.
NOTE:
Front wiper intermittent operation can be set to the operation with vehicle speed using CONSULT. Refer to
BCS-18, "WIPER : CONSULT Function - WIPER"
.
Front wiper intermittent operation with vehicle speed
• BCM calculates the intermittent operation delay interval from the following
- Vehicle speed signal
- Wiper intermittent dial position
Unit: Second
*: When operation setting is not linked with vehicle speed.
FRONT WIPER AUTO STOP OPERATION
• BCM stops transmitting the front wiper request signal when the front wiper switch is turned OFF.
• IPDM E/R detects the front wiper stop position signal from the front wiper motor and detects the front wiper
motor position (stop position/except stop position).
Wiper intermittent
dial position
Intermittent
operation
interval
Intermittent operation delay Interval
Vehicle speed
0 – 5 km/h
(0 – 3.1 MPH)
5 – 65 km/h
(3.1 – 40.4 MPH)*
65 km/h (40.4 MPH) or more
1
Short
↑
↓
Long
1
0.4
0.24
2
2.5
1
0.6
3
5
2
1.2
4
7.5
3
1.8
5
12.5
5
3
6
25
10
6
7
40
16
9.6
JPLIA1256GB
WW-10
< SYSTEM DESCRIPTION >
SYSTEM
• When the front wiper request signal is stopped, IPDM E/R turns ON the front wiper relay until the front wiper
motor returns to the stop position.
NOTE:
• BCM stops the transmitting of the front wiper request signal when the power switch is OFF.
• IPDM E/R turns the front wiper relay OFF when the power switch is OFF.
FRONT WIPER OPERATION LINKED WITH WASHER
• BCM transmits the front wiper request signal (LO) to IPDM E/R via CAN communication according to the
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 2 times
when the front washer switch OFF is detected.
Washer linked operating condition of front wiper
- Turn power switch ON
- Front washer switch ON (0.4 second or more)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
• The washer motor is grounded through the combination switch with the front washer switch ON.
FRONT WIPER SERVICE POSITION OPERATION
• Front wiper operates in LO, stops, and then stays in lock back position when front washer switch is turned
ON while power switch is OFF.
• BCM transmits front wiper service position signal via CAN communication according to the front wiper ser-
vice position function operating conditions.
Operation conditions of front wiper service position function
- Turn power switch OFF (within 1 minutes)
- Front washer switch ON (0.4 second or more)
• Front wiper operates at LO and then stops when IPDM E/R detects front wiper service position signal.
• Front wiper service position function is cancelled when front wiper washer switch is turned ON again within 1
minute after turning power switch OFF. If 1 minute or more is passed after turning power switch OFF, front
wiper service position function is cancelled when power switch is turned ON again, and then front wiper
switch (INT, LO, HI, MIST or WASHER) is turned ON.
NOTE:
Front wiper does not operate even if front wiper switch (INT, LO, or HI) is ON when power switch is turned ON
while front wiper is stopped according to front wiper service position function.
WIPER LINKED AUTO LIGHTING FUNCTION (EXCEPT FOR CANADA)
When light switch is in the AUTO position, front wiper operates, and then headlamp illuminates. Refer to
15, "AUTO LIGHT SYSTEM (EXCEPT FOR CANADA) : System Description"
.
FRONT WIPER AND WASHER SYSTEM : Fail-safe
INFOID:0000000010122200
FAIL
−SAFE OPERATION
IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to
REAR WIPER AND WASHER SYSTEM
JPLIA0410GB
SYSTEM
WW-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WIPER AND WASHER SYSTEM : System Description
INFOID:0000000010122201
SYSTEM DIAGRAM
OUTLINE
The rear wiper is controlled by each function of BCM.
Control by BCM
• Combination switch reading function
• Rear wiper control function
REAR WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM controls the rear wiper to start or stop.
REAR WIPER ON OPERATION
• BCM supplies power to the rear wiper motor according to the rear wiper ON operating condition.
Rear wiper ON operating condition
- Power switch ON
- Rear wiper switch ON
REAR WIPER INT OPERATION
• BCM supplies power to the rear wiper motor according to the INT operating condition.
Rear wiper INT operating condition
- Power switch ON
- Rear wiper switch INT
• BCM controls the rear wiper to operate once.
• BCM detects the rear wiper motor stopping position.
• BCM supplies power to the rear wiper motor after an intermittent from the stop of the rear wiper motor.
REAR WIPER AUTO STOP OPERATION
• BCM stops supplying power to the rear wiper motor when the rear wiper switch is turned OFF.
• BCM reads a rear wiper stop position signal from the rear wiper motor to detect a rear wiper motor position.
AWLIA2358GB
JPLIA1258GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст