Nissan Leaf. Manual — part 1027
PWC-26
< BASIC INSPECTION >
ADDITIONAL SERVICE WHEN REMOVING 12V BATTERY NEGATIVE TERMI-
NAL
ADDITIONAL SERVICE WHEN REMOVING 12V BATTERY NEGATIVE
TERMINAL
Description
INFOID:0000000010119938
When the 12V battery negative terminal is disconnected, the initialization is necessary for normal operation of
power window system.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000010119939
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
>> Inspection End.
ADDITIONAL SERVICE WHEN REPLACING POWER WINDOW MAIN SWITCH
PWC-27
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ADDITIONAL SERVICE WHEN REPLACING POWER WINDOW MAIN
SWITCH
Description
INFOID:0000000010119940
When the main power window and door lock/unlock switch replaced, the initialization in necessary for normal
operation of power window system.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000010119941
1.
SYSTEM INITIALIZATION
Perform system initialization. Refer to
>> GO TO 2.
2.
CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to
>> Inspection End.
PWC-28
< BASIC INSPECTION >
SYSTEM INITIALIZATION
SYSTEM INITIALIZATION
Description
INFOID:0000000010119942
If any of the following operations are performed, the initialization is necessary for normal operation of power
window system.
• Disconnection and connection of 12V battery cable from negative terminal.
• When main power window and door lock/unlock switch replaced.
• Electric power supply to main power window and door lock/unlock switch or front power window motor LH is
interrupted by blown fuse or disconnection and connection of the negative terminal of 12V battery, etc.
• Disconnection and connection of main power window and door lock/unlock switch harness connector.
• Removal of front power window motor LH from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000010119943
1.
STEP 1
1. Turn power switch ON.
2. Operate main power window and door lock/unlock switch to fully open the window. (This operation is
unnecessary if the window is already fully open)
3. Continue pulling the main power window and door lock/unlock switch UP (AUTO-UP operation). Even
after glass stops at fully closed position, keep pulling the switch for 2 seconds or more.
4. Check that AUTO-UP function operates normally.
>> GO TO 2.
2.
STEP 2
Check anti-pinch function. Refer to
>> Inspection End.
CHECK ANTI-PINCH FUNCTION
PWC-29
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
CHECK ANTI-PINCH FUNCTION
Description
INFOID:0000000010119944
If any of the following operations are performed, the initialization is necessary for normal operation of
anti-pinch function.
• Disconnection and connection of 12V battery cable from negative terminal.
• When main power window and door lock/unlock switch is replaced.
• Electric power supply to main power window and door lock/unlock switch or power window motor LH is
interrupted by blown fuse or disconnection and connection of the negative terminal of 12V battery, etc.
• Disconnection and connection of main power window and door lock/unlock switch harness connector.
• Removal of front power window motor LH from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
Work Procedure
INFOID:0000000010119945
1.
CHECK ANTI-PINCH FUNCTION
• Fully open the door window.
• Place a piece of wood near fully closed position.
• Close door glass completely with AUTO-UP.
• Check the following conditions
- Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops.
- Check that glass does not rise not when operating the main power window and door lock/unlock switch while
lowering.
CAUTION:
• Perform initial setting when AUTO-UP operation or anti-pinch function does not operate normally.
• Check that AUTO-UP operates before inspection when system initialization is performed.
• To prevent injury, do not check with hands and other body parts because they may be pinched. Do
not get pinched.
>> Inspection End.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст