Nissan Leaf. Manual — part 798
COMPRESSOR DISCHARGE REFRIGERANT TEMPERATURE SENSOR
HAC-195
< REMOVAL AND INSTALLATION >
[AUTO A/C (WITH HEAT PUMP)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Removal and Installation
INFOID:0000000010121900
REMOVAL
1. Remove the inner condenser assembly. Refer to
HA-61, "INNER CONDENSER : Removal and Installa-
2. Remove compressor discharge refrigerant temperature sensor from the inner condenser assembly.
INSTALLATION
Note the following items, and then install in the order of removal.
CAUTION:
• Mark the mounting position of compressor discharge refrigerant temperature sensor prior to
removal so that the reinstalled sensor can be located in the same position.
16. Evaporator cover
17. Inner condenser pipe cover
18. PTC heater shield LH
19. Inner condenser cover
20. Sleeve
21. Clip
22. Compressor discharge refrigerant
temperature sensor
23. Grommet
24. Gasket
25. Inner condenser
26. PTC heater outlet and A/C unit
case air temperature sensor as-
sembly
27. Heating and cooling unit
assembly case LH
28. Filter cover
29. Filter
30. Aspirator
31. Aspirator hose
32. Harness
33. PTC heater shield
34. Lower air mix door
35. Upper air mix door
36. Air mix door guide
37. Front door rod
38. Side ventilator door
39. Foot door
40. Side ventilator seal LH
41. Lower attachment case
42. Side ventilator seal RH
43. Center ventilator and defroster door 44. Sub defroster door
45. Upper attachment case
46. Defroster seal
47. Ventilator seal
48. Intake seal
49. Lower intake case
50. Intake door
51. Upper intake seal
52. Power transistor
53. Sub harness
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
HAC-196
< REMOVAL AND INSTALLATION >
[AUTO A/C (WITH HEAT PUMP)]
COMPRESSOR SUCTION REFRIGERANT TEMPERATURE SENSOR
COMPRESSOR SUCTION REFRIGERANT TEMPERATURE SENSOR
Exploded View
INFOID:0000000010121901
Removal and Installation
INFOID:0000000010121902
REMOVAL
1. Remove condenser assembly. Refer to
HA-52, "Removal and Installation"
2. Remove compressor suction refrigerant temperature sensor from the condenser assembly.
INSTALLATION
Note the following items, and then install in the order of removal.
CAUTION:
• Mark the mounting position of compressor suction refrigerant temperature sensor prior to removal
so that the reinstalled sensor can be located in the same position.
1.
Sleeve
2.
Clip
3.
Compressor suction refrigerant
temperature sensor
4.
Condenser pipe assembly
5.
O-ring
6.
Condenser
7.
Condenser support assembly
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMIIA2636GB
PTC HEATER OUTLET AND A/C UNIT CASE AIR TEMPERATURE SENSOR AS-
SEMBLY
HAC-197
< REMOVAL AND INSTALLATION >
[AUTO A/C (WITH HEAT PUMP)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
PTC HEATER OUTLET AND A/C UNIT CASE AIR TEMPERATURE SEN-
SOR ASSEMBLY
Exploded View
INFOID:0000000010121903
1.
Blower motor
2.
Blower case RH
3.
Blower case LH
4.
High voltage warning label
5.
PTC heater shield RH
6.
PTC heater
7.
Heating and cooling unit assembly
case RH
8.
Case packing
9.
Evaporator
JMIIA2600GB
HAC-198
< REMOVAL AND INSTALLATION >
[AUTO A/C (WITH HEAT PUMP)]
PTC HEATER OUTLET AND A/C UNIT CASE AIR TEMPERATURE SENSOR AS-
SEMBLY
Removal and Installation
INFOID:0000000010121904
REMOVAL
1. Remove the heating and cooling unit assembly. Refer to
HA-57, "HEATING AND COOLING UNIT
ASSEMBLY : Removal and Installation"
2. Remove PTC heater outlet and A/C unit case air temperature sensor assembly from the heating and cool-
ing unit assembly.
INSTALLATION
Install in the reverse order of removal.
10. Plate
11. O-rings
12. Grommet
13. Low pressure pipe flange
14. Intake sensor
15. PTC heater shield lower
16. Evaporator cover
17. Inner condenser pipe cover
18. PTC heater shield LH
19. Inner condenser cover
20. Sleeve
21. Clip
22. Compressor discharge refrigerant
temperature sensor
23. Grommet
24. Gasket
25. Inner condenser
26. PTC heater outlet and A/C unit
case air temperature sensor as-
sembly
27. Heating and cooling unit
assembly case LH
28. Filter cover
29. Filter
30. Aspirator
31. Aspirator hose
32. Harness
33. PTC heater shield
34. Lower air mix door
35. Upper air mix door
36. Air mix door guide
37. Front door rod
38. Side ventilator door
39. Foot door
40. Side ventilator seal LH
41. Lower attachment case
42. Side ventilator seal RH
43. Center ventilator and defroster door 44. Sub defroster door
45. Upper attachment case
46. Defroster seal
47. Ventilator seal
48. Intake seal
49. Lower intake case
50. Intake door
51. Upper intake seal
52. Power transistor
53. Sub harness
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст