Nissan Leaf. Manual — part 347
BRM-12
< PRECAUTION >
PROTECTION OF VEHICLE
PROTECTION OF VEHICLE
Protection of Vehicle
INFOID:0000000010121684
The seats, glass, and carpet must be removed or covered with appropriate material (spatter cover), according
to the type of work to be done, to prevent contamination and welding spatter.
In addition, when cutting the vehicle in an area close to high voltage parts or performing a welding operation,
the high voltage parts must be covered with a heat-resistant insulating cover (spatter cover).
REPAIRING MATERIAL
BRM-13
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
PREPARATION
REPAIRING MATERIAL
Foam Repair
INFOID:0000000010121685
During factory body assembly, foam insulators are installed in certain body panels and locations around the
vehicle. Use the following procedure(s) to replace any factory-installed foam insulators.
URETHANE FOAM APPLICATIONS
Use commercially available Urethane foam for sealant (foam material) repair of material used on vehicle.
Read instructions on product for fill procedures.
Example of foaming agent filling operation procedure
1. Fill procedures after installation of service part.
a. Eliminate foam material remaining on vehicle side.
b. Clean area after eliminating form insulator and foam material.
c. Install service part.
d. Insert nozzle into hole near fill area and fill foam material or fill enough to close gap with the service part.
2. Fill procedures before installation of service part.
a. Eliminate foam material remaining on vehicle side.
b. Clean area after eliminating foam insulator and foam material.
c. Fill foam material on wheelhouse outer side.
NOTE:
Fill enough to close gap with service part while avoiding flange
area.
d. Install service part.
NOTE:
Refer to label for information on working times.
<Urethane foam for foaming agent>
3M™ Automix™ Flexible Foam 08463 or equiva-
lent
1. Urethane foam
A. Nozzle insert hole
Front
1.
Urethane foam
A.
Fill while avoiding flange area
Front
JSKIA0129GB
JSKIA0130GB
BRM-14
< PREPARATION >
LOCATION OF PLASTIC PARTS
LOCATION OF PLASTIC PARTS
Precautions for Plastics
INFOID:0000000010121686
CAUTION:
• When repairing and painting a portion of the body adjacent to plastic parts, consider their characteristics (influence of heat
and solvent) and remove them if necessary or take suitable measures to protect them.
• Plastic parts should be repaired and painted using methods suiting the materials
,
characteristics.
Abbre-
viation
Material name
Heat resisting
temperature
°C (°F)
Resistance to gasoline and
solvents
Other cautions
PE
Polyethylene
60 (140)
Gasoline and most solvents are
harmless if applied for a very
short time (wipe out quickly).
Flammable
ABS
Acrylonitrile Butadiene Styrene
80 (176)
Avoid gasoline and solvents.
—
EPM/
EPDM
Ethylene Propylene (Diene) co-
polymer
80 (176)
Gasoline and most solvents are
harmless if applied for a very
short time (wipe out quickly).
Flammable
PS
Polystyrene
80 (176)
Avoid solvents.
Flammable
PVC
Poly Vinyl Chloride
80 (176)
Gasoline and most solvents are
harmless if applied for a very
short time (wipe out quickly).
Poisonous gas is emitted
when burned.
TPO
Thermoplastic Olefine
80 (176)
↑
Flammable
AAS
Acrylonitrile Acrylic Styrene
85 (185)
Avoid gasoline and solvents.
—
PMMA
Poly Methyl Methacrylate
85 (185)
↑
—
EVAC
Ethylene Vinyl Acetate
90 (194)
↑
—
PP
Polypropylene
90 (194)
Gasoline and most solvents are
harmless if applied for a very
short time (wipe out quickly).
Flammable, avoid bat-
tery acid.
PUR
Polyurethane
90 (194)
Avoid gasoline and solvents.
—
UP
Unsaturated Polyester
90 (194)
↑
Flammable
ASA
Acrylonitrile Styrene Acrylate
100 (212)
↑
Flammable
PPE
Poly Phenylene Ether
110 (230)
↑
—
TPU
Thermoplastic Urethane
110 (230)
↑
—
PBT+
PC
Poly Butylene Terephthalate +
Polycarbonate
120 (248)
↑
Flammable
PC
Polycarbonate
120 (248)
↑
—
POM
Poly Oxymethylene
120 (248)
↑
Avoid battery acid.
PA
Polyamide
140 (284)
↑
Avoid immersing in wa-
ter.
PBT
Poly Butylene Terephthalate
140 (284)
↑
—
PAR
Polyarylate
180 (356)
↑
—
PET
Polyethylene terephthalate
180 (356)
↑
—
PEI
Polyetherimide
200 (392)
↑
—
LOCATION OF PLASTIC PARTS
BRM-15
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Location of Plastic Parts
INFOID:0000000010121687
Component
Material
Component
Material
1
Side roof molding
PVC + Stainless
9
Door outside molding
PVC + Stainless
Lower side molding
ASA
10
Rear combination lamp
Lens
PMMA
2
Upper windshield molding
TPO
Housing
ASA
3
Front side marker lamp
Lens
PMMA
11
Rear spoiler
ABS
Housing
PP
12
High mount stop lamp
Lens
PMMA
4
Front combination lamp
Lens
PC
Housing
ABS
Housing
PP
13
Back door handle
ABS
5
Charge port lid
PC + PET
14
License plate lamp
Lens
PMMA
6
Bumper fascia
PP + EPM
Housing
PC
7
Front fender protector
PP
15
Reflex reflector
Lens
PMMA
8
Door outside mirror
Case
PP + Glass fiber
Housing
ABS
Base
PBT + PET +
Glass fiber
16
Door outside handle
Grip body
PC + PET +
Glass fiber
Cover
ABS
Grip cover
PC + ABS
AWKIA2379ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст