Nissan Leaf. Manual — part 1096
CURTAIN AIR BAG MODULE
SR-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000010120261
Removal and Installation
INFOID:0000000010120262
WARNING:
Always observe the following items for preventing accidental activation.
• Before servicing, turn the ignition switch off, disconnect both 12V battery terminals and wait at least
three minutes.
• Always work from the side of curtain air bag module. Never work in front of it.
• Never use air tools or electric tools for servicing.
REMOVAL
1. Disconnect the negative and positive 12V battery terminals and wait at least three minutes. Refer to
89, "Removal and Installation"
2. Remove headlining assembly. Refer to
INT-37, "Removal and Installation"
.
3. Remove the curtain air bag module mounting bolt that is located on the front pillar.
1.
Curtain air bag module
: Metal clip
: N·m (kg-m, ft-lb)
JMHIA1740GB
SR-30
< REMOVAL AND INSTALLATION >
CURTAIN AIR BAG MODULE
4. Disengage metal clips on the front roof.
a. Fully insert a flat-bladed screwdriver (A) into center of metal clip.
b. Lift the flat-bladed screwdriver upward according to the numerical order 1
→ 2 as shown in the figure and
disengage upper side of metal clip.
c.
Rotate the flat-bladed screwdriver as shown in the figure and disengage lower side of metal clip.
CAUTION:
Never deform metal clip.
5. Disconnect curtain air bag module harness connector.
CAUTION:
• For installing/removing the curtain air bag harness con-
nector, insert a thin screwdriver wrapped in tape into
notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed securely into it.
6. Remove the curtain air bag module mounting bolts that are located on the rear pillar.
7. Remove the curtain air bag module mounting bolts that are located on the inflator, and then remove cur-
tain air bag module.
CAUTION:
• To prevent damage to the parts, never impact the curtain
air bag module.
• Replace the curtain air bag module if it is dropped or sus-
tains an impact.
• To prevent accidental explosion, never insert any foreign objects (screwdriver, etc.) into the cur-
tain air bag module.
• To prevent accidental explosion, never disassemble the curtain air bag module.
• To prevent accidental explosion, never expose the curtain air bag module to temperature of more
than 90
°C (194°F).
• To prevent damage to the parts, never allow oil, grease, detergent, or water to come in contact
with the curtain air bag module.
INSTALLATION
: Metal clip
JMHIA1615ZZ
PHIA0953J
JMHIA0009ZZ
CURTAIN AIR BAG MODULE
SR-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Insert metal clips of front roof until a locking sound is heard. Pull metal clips and check that it is fully
locked to the vehicle body.
• Check perforation of curtain air bag module to check that curtain air bag module is not twisted.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
SR-32
< REMOVAL AND INSTALLATION >
SIDE AIR BAG MODULE
SIDE AIR BAG MODULE
Removal and Installation
INFOID:0000000010120263
The front side air bag module is part of the front seatback. For removal and installation of the front seatback,
SE-30, "SEATBACK : Disassembly and Assembly"
.
NOTE:
If the vehicle has been involved in a collision and the front side air bag has deployed, the front seatback must
be replaced.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст