Nissan Leaf. Manual — part 674
FRONT BUMPER
EXT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Bumper fascia assembly – Hood
C – C
2.3 – 7.7 mm
(0.012 – 0.130 in)
[(
−1.0) – (+3.0) mm]
[(
−0.039 – (+0.118) in]
Bumper fascia assembly – Front
combination lamp
D – D
0.2 – 3.8 mm
(0.008 – 0.150 in)
—
Front bumper – Front fender
E – E
0.3 – 1.0 mm
(0.012 – 0.039 in)
[(
−0.3) – (+1.7) mm]
[(
−0.012) – (+0.067) in]
Portion
Clearance
Surface height difference
EXT-16
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded View
INFOID:0000000010119988
1.
Bumper closing LH
2.
Grommet
3.
Rear side bracket LH
4.
Bumper stay LH
5.
Bumper reinforcement
6.
Bumper energy absorber LH
7.
Bumper fascia
8.
Grommet
9.
License lamp bracket
10. Bumper energy absorber RH
11. Bumper closing RH
12. Rear side bracket RH
13. Bumper stay RH
JMKIA6461GB
REAR BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000010119989
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1. Remove rear combination lamps (RH/LH). Refer to
EXL-140, "Removal and Installation"
.
2. Remove bumper fascia upper side fixing screws (A) (LH/RH).
3. Remove bumper fascia lower side fixing bolts and clips.
4. Remove bumper fascia side fixing screws (A) (LH/RH).
5. Apply protective tape on the part to protect it from damage.
: N·m (kg-m, ft-lb)
, , , : Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA6442ZZ
JMKIA6443ZZ
JMKIA9374ZZ
EXT-18
< REMOVAL AND INSTALLATION >
REAR BUMPER
6. Pull bumper fascia side toward the vehicle side to disengage the
fitting of bumper side bracket and bumper fascia side as shown
by the arrow in the figure.
7. Disengage license lamp harness connectors.
8. Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
9. Remove the following parts after removing bumper fascia.
• License lamps (LH and RH). Refer to
EXL-146, "Removal and Installation"
• Bumper closings (LH and RH)
• Bumper side brackets (LH and RH)
• Reflectors (LH and RH) Refer to
EXL-148, "Removal and Installation"
.
10. Remove bumper energy absorbers (LH and RH).
11. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
: Pawl
JMKIA6444ZZ
JMKIA6445ZZ
Portion
Clearance
Surface height difference
Bumper fascia assembly –
Rear fender
A – A
0.3 – 1.0 mm
(0.012 – 0.039 in)
[(
−0.3) – (+1.7) mm]
[(
−0.012 – (+0.067) in]
Bumper fascia assembly –
Rear combination lamp
B – B
0.4 – 3.6 mm
(0.016 – 0.142 in)
—
Bumper fascia assembly –
Back door
C – C
3.3 – 7.3 mm
(0.130 – 0.287 in)
—
D – D
6.0 – 10.0 mm
(0.236 – 0.394 in)
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст