Nissan Leaf. Manual — part 882
INSTRUMENT PANEL ASSEMBLY
IP-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
1. Apply protective tape (A) around the part to protect from
damage.
2. Insert suitable tool (A) between charging status indicator
and instrument panel assembly to disengage the pawl and
metal clips as shown.
3. Pull toward the arrow direction.
4. Disconnect harness connector.
21. Remove switch panel.
1. Apply protective tape (A) around the part to protect from damage.
2. Insert suitable tool (A) between switch panel and instrument
panel assembly to disengage the pawls as shown.
3. Pull up switch panel, then disconnect harness connectors.
22. Release front pillar portion of front body side welt RH. Refer to
INT-29, "BODY SIDE WELT : Removal and
.
23. Remove front pillar garnish RH. Refer to
INT-26, "FRONT PILLAR GARNISH : Removal and Installation"
24. Remove instrument mask RH.
JMJIA6995ZZ
: Pawl
: Metal clip
JMJIA6996ZZ
JMJIA6997ZZ
: Pawl
JMJIA6998ZZ
IP-24
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
1. Apply protective tape (A) around the part to protect from
damage.
2. Insert suitable tool (A) between instrument mask RH and
instrument panel assembly to disengage the pawls accord-
ing to numerical order 1
→ 3 the as shown.
3. Pull back instrument mask RH.
25. Remove instrument under cover RH.
1. Insert suitable tool between instrument under cover RH and glove box cover assembly to disengage
the pawls and metal clips as shown.
2. Pull downward and disengage metal clips of the back side.
3. Pull back instrument under cover RH.
26. Remove glove box lid.
1. Open glove box lid.
2. Disengage the pawl, then remove damper pin on left side.
CAUTION:
Do not excessively pull string of glove box damper.
JMJIA6999ZZ
: Pawl
JMJIA7000ZZ
: Pawl
JMJIA7003ZZ
INSTRUMENT PANEL ASSEMBLY
IP-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
3. Pull glove box lid (1) toward vehicle rear, then disengage
the joint from glove box cover assembly (2).
27. Remove glove box cover assembly.
1. Remove screws (A).
2. Pull back the glove box cover assembly while holding the
lower side and disengage the pawl and metal clips accord-
ing to numerical order 1
→ 3 the as shown.
28. Disconnect passenger air bag module harness connector. Refer to
29. Remove passenger air bag module bolt. Refer to
30. Remove instrument panel assembly.
1. Remove instrument panel assembly bolt (A) and screws (B).
CAUTION:
Cover tool with a shop cloth to prevent windshield glass from being damaged.
2. Disconnect TCU harness connector (A) (if equipped) and remove harness clip (B).
JMJIA5021ZZ
: Pawl
: Metal clip
JMJIA5022ZZ
JMJIA5023ZZ
JMJIA7004ZZ
IP-26
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
3. Disconnect power socket harness connector. Refer to
PWO-6, "Removal and Installation"
4. Disengage harness (A) and harness (B) of front pillar LH and RH portions from instrument panel
assembly.
5. Remove harness clips (C) from instrument panel assembly.
6. Disconnect harness connector (D).
7. Remove instrument panel from passenger door opening portion.
CAUTION:
• Cover center console upper surface with a shop cloth to prevent it from being damaged.
• When removing instrument panel assembly, two workers are required to prevent from drop-
ping.
31. Remove the following parts after removing instrument panel assembly.
• Passenger air bag module: Refer to
SR-26, "Removal and Installation"
.
• Side ventilator grille RH: Refer to
VTL-13, "SIDE VENTILATOR GRILLE : Removal and Installation"
.
• Side defroster nozzle LH/RH: Refer to
VTL-16, "SIDE DEFROSTER DUCT : Removal and Installation -
.
• Side defroster grille LH/RH: Refer to
VTL-14, "SIDE DEFROSTER GRILLE : Removal and Installation"
• Center ventilator duct: Refer to
VTL-15, "CENTER VENTILATOR DUCT : Removal and Installation"
.
• Side ventilator duct: Refer to
VTL-15, "SIDE VENTILATOR DUCT : Removal and Installation"
• Front defroster nozzle. Refer to
VTL-15, "FRONT DEFROSTER DUCT : Removal and Installation"
• GPS antenna (if equipped): Refer to
AV-323, "Removal and Installation"
.
• TEL antenna (if equipped): Refer to
AV-597, "Removal and Installation"
.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
JMJIA5025ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст