Nissan Leaf. Manual — part 1043
REAR SUSPENSION BEAM
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION BEAM
Exploded View
INFOID:0000000010119462
Removal and Installation
INFOID:0000000010119463
REMOVAL
1. Remove wheel and tire using power tool. Refer to
2. Drain brake fluid. Refer to
3. Remove wheel sensor and sensor harness. Refer to
BRC-159, "REAR WHEEL SENSOR : Removal and
.
4. Remove brake caliper assembly. Refer to
BR-526, "BRAKE CALIPER ASSEMBLY : Removal and Instal-
.
5. Remove disc rotor. Refer to
RAX-7, "Removal and Installation"
.
6. Remove parking brake shoe assembly. Refer to
PB-12, "Removal and Installation"
7. Remove parking brake cable from back plate and rear suspension beam. Refer to
.
8. Separate brake hose and brake tube. Refer to
BR-507, "REAR : Removal and Installation"
.
9. Set suitable jack under rear suspension beam.
CAUTION:
• Do not damage the suspension beam with a jack.
• Check the stable condition when using a jack.
1.
Rear suspension beam
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JPEIB0271GB
RSU-14
< REMOVAL AND INSTALLATION >
REAR SUSPENSION BEAM
10. Remove shock absorber bolts (lower side) (1) using power tool.
RSU-8, "Removal and Installation"
11. Remove coil spring. Refer to
RSU-11, "Removal and Installa-
12. Remove rear suspension beam bolts and nuts.
13. Slowly lower jack, remove rear suspension beam from vehicle.
CAUTION:
Operate while checking that jack supporting status is sta-
ble.
14. Remove wheel hub assembly using power tool. Refer to
15. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Do not reuse rear suspension beam nut.
• Perform final tightening of rear suspension beam installation position (rubber bushing), under unladen condi-
tions with tires on level ground.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010119464
INSPECTION AFTER REMOVAL
Check rear suspension beam for deformation, cracks or damage. Replace the part if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to
.
2. Adjust parking brake. Refer to
.
3. Check wheel alignment. Refer to
JPEIB0239ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000010119465
Measure value under unladen
*
conditions.
*: Fluids and lubricants are full. Tire repair kit and mats are in designated positions.
Wheelarch Height
INFOID:0000000010119466
UNITED STATES
Measure value under unladen* conditions.
*:Fluids and lubricants are full. Tire repair kit and mats are in designated positions.
Tire size
205/55R16
215/50R17
Camber
Degree minute (Decimal degree)
Minimum
0
° 59′ (0.98°)
Nominal
1
° 29′ (1.48°)
Maximum
1
° 59′ (1.98°)
Toe-in
Distance (A - B)
Minimum
Out 1.5 mm (Out 0.059 in) Out 1.6 mm (Out 0.063 in)
Nominal
In 3.3 mm (In 0.130 in)
In 3.4 mm (In 0.134 in)
Maximum
In 8.1 mm (In 0.319 in)
In 8.4 mm (In 0.331 in)
Angle (LH and RH)
Degree minute (Decimal degree)
Minimum
Out 0
° 09′ (Out 0.15°)
Nominal
In 0
° 19′ (In 0.32°)
Maximum
In 0
° 47′ (In 0.78°)
SFA234AC
LEIA0085E
Tire size
205/55R16
215/50R17
Front (Hf)
706 mm (27.80 in)
714 mm (28.11 in)
Rear (Hr)
708 mm (27.87 in)
714 mm (28.11 in)
RSU-16
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
CANADA
Measure value under unladen* conditions.
*:Fluids and lubricants are full. Tire repair kit and mats are in designated positions.
LEIA0085E
Tire size
205/55R16
215/50R17
Front (Hf)
706 mm (27.80 in)
714 mm (28.11 in)
Rear (Hr)
709 mm (27.91 in)
715 mm (28.15 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст