Nissan Leaf. Manual — part 482
LI-ION BATTERY
EVB-211
< UNIT DISASSEMBLY AND ASSEMBLY >
D
E
F
G
H
I
J
K
L
M
A
B
EVB
N
O
P
16. Remove the bus bar mounting nut which connects the current
sensor and left front module stack .
DANGER:
•
There is the danger of electric shock caused by
contact with the terminals. Be sure to wear insulated pro-
tective gear and use insulated tools.
•
Because of the danger of electric shock, be sure to
close the bus bar cover after removing the bus bar.
17. Remove the service plug switch bracket mounting bolts .
WARNING:
To prevent electric shock, wear insulated protective
gear and use insulated tools.
18. Invert the service plug switch bracket and remove the high-volt-
age harness mounting bolt , current sensor mounting bolt ,
and the connector , then remove the service plug switch
bracket .
DANGER:
•
There is the danger of electric shock caused by
contact with the terminals. Be sure to wear insulated pro-
tective gear and use insulated tools.
•
Because there is a risk of electric shock, immediately protect the terminals of the discon-
nected high-voltage harness connector (high-voltage terminals) with insulating tape so that they
are not exposed.
19. Remove the mounting nuts , then remove high-voltage harness and .
JSCIA0596ZZ
JSCIA0597ZZ
JSCIA0598ZZ
EVB-212
< UNIT DISASSEMBLY AND ASSEMBLY >
LI-ION BATTERY
DANGER:
•
There is the danger of electric shock caused by contact with the terminals. Be sure to wear
insulated protective gear and use insulated tools.
•
Because of the danger of electric shock, be sure to close the bus bar cover after removing
the bus bar.
20. Remove the vehicle communications harness and voltage detection harness.
WARNING:
To prevent electric shock, wear insulated protective gear and use insulated tools.
: Harness clip
JSCIA0764ZZ
Vehicle communications harness
Voltage detection harness
Snap ring
: Harness clip
JSCIA0765ZZ
LI-ION BATTERY
EVB-213
< UNIT DISASSEMBLY AND ASSEMBLY >
D
E
F
G
H
I
J
K
L
M
A
B
EVB
N
O
P
ASSEMBLY
Note the following items, and disassembly in the reverse order of disassembly.
DANGER:
•
There is the danger of electric shock caused by contact with the terminals. Be sure to wear
insulated protective gear and use insulated tools.
•
Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong ter-
minal.
- If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.
- Always keep the bus bar cover closed until immediately before the installation of bus bar.
- Since the correct installation position for the bus bar connected to both front module stacks is com-
monly-confused with the wrong position , install the bus bar to the correct position with extreme
caution.
WARNING:
Install the Li-ion battery controller immediately before installing the battery pack upper case. Refer to
EVB-201, "LI-ION BATTERY CONTROLLER : Removal and Installation"
.
CAUTION:
• Perform the “LI-ION BATTERY JUNCTION BOX DATA CLEAR” when battery junction box is replaced.
Refer to
• Be sure to reinstall the high voltage harness clips in their original positions. If a clip is damaged,
replace it with a new clip before installing.
• Check the following items after installing battery pack: Refer to
AIR LEAK INSPECTION
ELECTRIC EQUIPOTENTIAL TEST
LI-ION BATTERY HEATER
Correct position
Wrong position
: Battery front
JSCIA0873ZZ
EVB-214
< UNIT DISASSEMBLY AND ASSEMBLY >
LI-ION BATTERY
LI-ION BATTERY HEATER : Exploded view
INFOID:0000000010121180
Li-ion battery heater RR2
Li-ion battery heater RH2
Li-ion battery heater RH1
Li-ion battery heater LH1
Li-ion battery heater LH2
Li-ion battery heater relay unit
JSCIA0750GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст