Nissan Leaf. Manual — part 187
C1A61 MOTOR
BR-69
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
10.
PERFORM SELF-DIAGNOSIS (4)
With CONSULT
1. Connect the electrically-driven intelligent brake unit harness connector.
2. Connect 12V battery cable to negative terminal.
3. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
4. Repeat step 3 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
5. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
6. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
7. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
8. Start CONSULT and erase self-diagnosis result of “BRAKE”.
9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
11. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
12. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
13. Release brake pedal.
14. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A61” detected?
YES
>> GO TO 11.
NO
>> INSPECTION END
11.
CHECK GROUND CIRCUIT
1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
3. Disconnect 12V battery cable from negative terminal. Refer to
BR-6, "Precaution for Removing 12V Bat-
4. Disconnect the electrically-driven intelligent brake unit harness connector.
5. Check the continuity between electrically-driven intelligent brake unit and ground.
Is the inspection result normal?
YES
>> GO TO 13.
NO
>> Repair or replace error-detected parts and GO TO 12.
12.
PERFORM SELF-DIAGNOSIS (5)
With CONSULT
1. Connect the electrically-driven intelligent brake unit harness connector.
2. Connect 12V battery cable to negative terminal.
3. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Electrically-driven intelligent brake unit
—
Continuity
Connector
Terminal
E34
32
Ground
Existed
BR-70
< DTC/CIRCUIT DIAGNOSIS >
C1A61 MOTOR
Never set the vehicle to READY.
4. Repeat step 3 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
5. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
6. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
7. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
8. Start CONSULT and erase self-diagnosis result of “BRAKE”.
9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
11. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
12. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
13. Release brake pedal.
14. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A61” detected?
YES
>> GO TO 13.
NO
>> INSPECTION END
13.
CHECK DATA MONITOR
With CONSULT
1. Connect the electrically-driven intelligent brake unit harness connector.
2. Connect 12V battery cable to negative terminal.
3. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
4. Repeat step 3 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
5. Start CONSULT and select “BRAKE” and “DATA MONITOR” according this order.
6. Check the “MOTOR POWER SUPPLY” and “CONTROL MODULE POWER”. Refer to
Is the inspection result normal?
YES
>> GO TO 14.
NO
>> Replace the electrically-driven intelligent brake unit. Refer to
BR-510, "Removal and installation"
14.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
1. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
2. Repeat step 1 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
5. Turn the power switch ON without depressing the brake pedal.
CAUTION:
C1A61 MOTOR
BR-71
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Never set the vehicle to READY.
6. Start CONSULT and erase self-diagnosis result of “BRAKE”.
7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
9. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
11. Release brake pedal.
12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A61” detected?
YES
>> Replace the electrically-driven intelligent brake unit. Refer to
BR-510, "Removal and installation"
NO
>> INSPECTION END
BR-72
< DTC/CIRCUIT DIAGNOSIS >
C1A62 CONTROL MODULE
C1A62 CONTROL MODULE
DTC Logic
INFOID:0000000010123008
DTC DETECTION LOGIC
DTC REPRODUCTION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn power switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
2. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A62” detected?
YES
>> Proceed to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010123009
1.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
1. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
2. Start CONSULT and perform “BRAKE” self-diagnosis.
“PAST” or “CRNT” shown in self-diagnosis results (“C1A62”)?
YES (“PAST”)>>GO TO 2.
YES (“CRNT”)>>GO TO 6.
NO
>> INSPECTION END
2.
INTERVIEW FROM THE CUSTOMER (1)
Check to see if there is a removal history of 12V battery or 12V battery terminals.
Is there a removal history of 12V battery or 12V battery terminals?
YES
>> GO TO 3.
NO
>> GO TO 6.
DTC
Display item
Malfunction detection condition
Possible causes
C1A62
CONTROL MODULE POWER
SUPPLY
• Power voltage of control module that is integrat-
ed with electrically-driven intelligent brake unit is
as shown below.
- Control module power voltage: 9 V
≥ Control
module power voltage
- Control module power voltage: 16 V
≤ Control
module power voltage
• After turning the power switch OFF, 12V battery
terminals are disconnected with any door open
(including back door).
• After turning the power switch OFF, 12V battery
terminals are disconnected without waiting for 3
minutes or more after closing all doors (including
back door).
• Harness or connector
• Electrically-driven intelligent
brake unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст