Nissan Leaf. Manual — part 753
PRECAUTIONS
HAC-15
< PRECAUTION >
[AUTO A/C (WITH HEAT PUMP)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
SERVICE COUPLERS
Never attempt to connect HFC-134a (R-134a) service couplers to
the CFC-12 (R-12) A/C system. The HFC-134a (R-134a) couplers
do not properly connect to the CFC-12 (R-12) system. However, if an
improper connection is attempted, discharging and contamination
may occur.
REFRIGERANT WEIGHT SCALE
Verify that no refrigerant other than HFC-134a (R-134a) and speci-
fied lubricants have been used with the scale. The hose fitting must
be 1/2
″-16 ACME if the scale controls refrigerant flow electronically.
CALIBRATING ACR4 WEIGHT SCALE
Calibrate the scale each three month.
To calibrate the weight scale on the ACR4:
1. Press “Shift/Reset” and “Enter” at the same time.
2. Press “8787”. “A1” is displayed.
3. Remove all weight from the scale.
4. Press “0”, then press “Enter”. “0.00” is displayed and change to “A2”.
5. Place a known weight (dumbbell or similar weight), between 4.5 and 8.6 kg (10 and 19 lb.) on the center
of the weight scale.
6. Enter the known weight using four digits. (Example 10 lb. = 10.00, 10.5 lb. = 10.50)
7. Press “Enter” — the display returns to the vacuum mode.
8. Press “Shift/Reset” and “Enter” at the same time.
9. Press “6” — the known weight on the scale is displayed.
10. Remove the known weight from the scale. “0.00” is displayed.
11. Press “Shift/Reset” to return the ACR4 to the program mode.
CHARGING CYLINDER
Using a charging cylinder is not recommended. Refrigerant may be vented into air from cylinder’s top valve
when filling the cylinder with refrigerant. Also, the accuracy of the cylinder is generally less than that of an
electronic scale or of quality recycle/recharge equipment.
Shut-off valve rotation
A/C service valve
Clockwise
Open
Counterclockwise
Close
RHA273D
RHA274D
HAC-16
< PREPARATION >
[AUTO A/C (WITH HEAT PUMP)]
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000010121726
Tool name
Description
Service hoses
• High-pressure side hose
• Low-pressure side hose
• Utility hose
Hose color:
• Low-pressure side hose: Blue with
black stripe
• High-pressure side hose: Red with
black stripe
• Utility hose: Yellow with black stripe
or green with black stripe
Hose fitting to gauge:
• 1/2
″
-16 ACME
Insulated gloves
Comply with EN60903:
• Use protective gloves made of
insulating material.
• The protective gloves must be
capable of resisting the voltage
of 600 or more.
Removing and installing high voltage
components
Leather gloves
[Use leather gloves that can fas-
ten the wrist tight]
• Removing and installing high volt-
age components
• Protect insulated gloves
Insulated safety shoes
Comply with EN60903:
• Use protective shoes made of
insulating material.
• The protective shoes must be
capable of resisting the voltage
of 600 or more.
Removing and installing high voltage
components
Face shield
[Comply with EN166.]
• Removing and installing high volt-
age components
• To protect face from the spatter on
the work to electric line
Insulated helmet
Removing and installing high voltage
components
S-NT201
JMCIA0149ZZ
JPCIA0066ZZ
JPCIA0011ZZ
JPCIA0167ZZ
JPCIA0013ZZ
PREPARATION
HAC-17
< PREPARATION >
[AUTO A/C (WITH HEAT PUMP)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Insulation resistance tester
(Multi tester)
Measuring insulation resistance,
voltage and resistance
(J-48710)
NISSAN ACR2009 RRR Unit
Refrigerant recovery, recycling and
recharging
(J-41995)
Electrical leak detector
Power supply:
DC12V (Battery terminal)
Manifold gauge set
(with hoses and couplers)
Identification:
• The gauge face indicates HFC-
134a (R-134a).
Fitting size: Thread size
• 1/2
″
-16 ACME
Service couplers
• High-pressure side coupler
• Low-pressure side coupler
Hose fitting to service hose:
M14 x 1.5 fitting is optional or perma-
nently attached.
Refrigerant weight scale
For measuring of refrigerant
Fitting size: Thread size
1/2
″
-16 ACME
Vacuum pump
(Including the isolator valve)
Capacity:
• Air displacement: 4 CFM
• Micron rating: 20 microns
• Oil capacity: 482 m (17 Imp fl oz.)
Fitting size: Thread size
• 1/2
″
-16 ACME
Tool name
Description
JPCIA0014ZZ
WJIA0293E
AHA281A
RJIA0196E
S-NT202
S-NT200
S-NT203
HAC-18
< PREPARATION >
[AUTO A/C (WITH HEAT PUMP)]
PREPARATION
Special Service Tool
INFOID:0000000010121727
The actual shape of the tools may differ from those illustrated here.
Oil and Grease
INFOID:0000000010121728
Tool number
(TechMate No.)
Tool name
Description
—
(J-46534)
Trim tool set
Removing trim components
AWJIA0483ZZ
Name
Application
Note
Refrigerant can (HFC-134a)
Charging refrigerant
—
Compressor oil (ND-OIL11)
Refilling compressor oil
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст