Nissan Leaf. Manual — part 1138
ST-44
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
STEERING GEAR AND LINKAGE
5. Adjust inner socket to standard length (L), and then tighten lock
nut (1) to the specified torque. Check length again after tighten-
ing lock nut.
CAUTION:
• When tightening the lock nut (1), be sure to fix outer
socket (2) with a wrench or an equivalent to prevent the
ball joint from getting contact with the knuckle.
• Adjust toe-in after this procedure. The length achieved
after toe-in adjustment is not necessary the above value.
Inspection
INFOID:0000000010119110
INSPECTION AFTER DISASSEMBLY
Boot
• Check boot for cracks, and replace it if a malfunction is detected.
Gear housing Assembly
• Check gear housing assembly for damage and scratches. Replace if there are any abnormal conditions.
Outer Socket and Inner Socket
• Check the following items and replace the component if it does not meet the standard.
BALL JOINT SWINGING FORCE
• Hook the Tool at the measuring point and pull the Tool. Make sure
that the Tool reads the specified value when ball stud and inner
socket start to move. Replace outer socket or steering gear
assembly (inner socket) if they are outside the standard.
BALL JOINT AXIAL END PLAY
Inner socket length (L) : Refer to
.
JPGIA0187ZZ
JSGIA0538ZZ
Measuring point of outer socket (1)
: Ball stud upper side (A)
Measuring point of inner socket (2)
: Point (B) shown in the figure
Tool number
: — (J-44372)
Swinging force : Refer to
JPGIA0188ZZ
STEERING GEAR AND LINKAGE
ST-45
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Apply an axial load of 490 N (50 kg, 110 lb) to ball stud. Measure
the amount of stud movement, and then make sure that the value
is within the following specified range. Replace outer socket (1) or
steering gear assembly (inner socket) (2) if the measured value is
outside the standard.
INSPECTION AFTER INSTALLATION
• Check if steering wheel turns smoothly when it is turned several times fully to the end of the left and right.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle.
- Steering wheel play: Refer to
.
- Neutral position steering wheel, steering wheel turning force, and front wheel turning angle: Refer to
• Adjust neutral position of steering angle sensor. Refer to
.
Axial end play : Refer to
JSGIA0109ZZ
ST-46
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
HEATED STEERING WHEEL SWITCH
HEATED STEERING WHEEL SWITCH
Removal and Installation
INFOID:0000000010119111
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-17, "Removal and Installation"
.
2. Remove switch panel. Refer to
IP-17, "Removal and Installation"
.
3. Remove heated steering wheel switch (1) from switch panel
while pushing the pawl.
INSTALLATION
Install in the reverse order of removal.
JSGIA0901ZZ
SERVICE DATA AND SPECIFICATIONS (SDS)
ST-47
< SERVICE DATA AND SPECIFICATIONS (SDS)
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000010119112
Steering Wheel
INFOID:0000000010119113
Steering Angle
INFOID:0000000010119114
Unit: Degree minute (Decimal degree)
Steering Column
INFOID:0000000010119115
*: For measuring position, refer to
Steering Gear and Linkage
INFOID:0000000010119116
*: For measuring position, refer to
Steering gear model
R25N
Item
Standard
Steering wheel axial end play
0 mm (0 in)
Steering wheel play on the outer circumference
0 - 35 mm (0 - 1.38 in)
Steering wheel turning force
36 N (3.7 kg-f, 8.1 lb-f) or less
Tire Size
205/55R16
215/50R17
Inner wheel
Minimum
37
° 00′ (37.0°)
34
° 00′ (34.0°)
Nominal
40
° 00′ (40.0°)
37
° 00′ (37.0°)
Maximum
41
° 00′ (41.0°)
38
° 00′ (38.0°)
Outer wheel
Nominal
33
° 00′ (33.0°)
32
° 00′ (32.0°)
Rotating torque
0 – 2.1 N·m (0 – 0.21 kg-m, 0 – 19 in-lb)
Steering column length
*
460.1mm (18.11in)
Tilt operating range
*
40.0 mm (1.575 in)
Tire Size
205/55R16
215/50R17
Rack stroke neutral position
73 mm (2.87 in)
70 mm (2.76 in)
Inner socket length
82.4 mm (3.244 in)
Outer socket ball joint
Swing force
*
(Spring balance measurement)
6.0 – 58 N (0.61 – 5.9 kg-f, 1.35 – 13.0 lb-f)
Axial end play
0.5 mm (0.020 in) or less
Inner socket ball joint
Swing force
*
(Spring balance measurement)
4.3 – 43.1 N (0.44 – 4.40 kg-f, 0.97 – 9.69 lb-f)
Axial end play
0.2 mm (0.008 in) or less
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст