Nissan Leaf. Manual — part 666
FRONT COMBINATION LAMP
EXL-265
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000010121487
REMOVAL
DISASSEMBLY
Front combination lamp
Removal and Installation
INFOID:0000000010121488
CAUTION:
1.
Front side marker lamp
2.
Front combination lamp
: N·m (kg-m, in-lb)
JMLIA2081GB
ALLIA1271ZZ
1.
Housing assembly
2.
Front turn signal lamp bulb
3.
Front turn signal lamp bulb socket
4.
Harness
5.
Halogen bulb
: Vehicle front
EXL-266
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
FRONT COMBINATION LAMP
Disconnect the 12V battery negative terminal or remove the fuse to electric leakage. Refer to
"Precaution for Removing 12V Battery"
REMOVAL
1. Remove front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
2. Remove front side marker lamp mounting bolts.
3. Pull up front side marker lamp, disconnect the front side marker lamp harness connector and remove the
front side marker lamp.
4. Remove front combination lamp mounting bolts.
5. Pull out front combination lamp forward the vehicle, and then disconnect the connector before removing
front combination lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Bulb Replacement
INFOID:0000000010121489
CAUTION:
• Disconnect the 12V battery negative terminal or remove the fuse to electric leakage. Refer to
151, "Precaution for Removing 12V Battery"
.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage to the bulb.
• Never touch bulb by hand while it is lit or right after being turned off to prevent a burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1. Rotate resin cap (1) counterclockwise and unlock it.
2. Rotate headlamp bulb (2) counterclockwise and unlock it.
3. Disconnect headlamp bulb from the harness connector (1) and
remove.
FRONT TURN SIGNAL LAMP BULB
1. Rotate bulb socket counterclockwise and unlock it.
2. Remove bulb from the bulb socket.
ALLIA1272ZZ
ALLIA1273ZZ
FRONT COMBINATION LAMP
EXL-267
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Disassembly and Assembly
INFOID:0000000010121490
DISASSEMBLY
1. Rotate resin cap counterclockwise and unlock it.
2. Rotate headlamp bulb counterclockwise and unlock it.
3. Disconnect headlamp bulb harness connector.
4. Rotate front turn signal lamp bulb socket counterclockwise and unlock it.
5. Remove front turn signal lamp bulb from bulb socket.
6. Remove combination lamp harness connector.
ASSEMBLY
Assembly is in the reverse order of disassembly.
Installing service bracket
INFOID:0000000010121491
If only installation part (A) as shown in the figure is damaged, and
front combination lamp housing itself is not damaged, repair can be
completed easily by installing service brackets.
Removal
1. Remove front combination lamp. Refer to
EXL-265, "Removal and Installation"
.
2. Cut damaged section of installation part, then shape with sandpaper.
Installation
1. Install service bracket (1) to headlamp housing (2) with screws.
2. Install front combination lamp to the vehicle.
JMLIA1779ZZ
1.
Front combination lamp RH
2.
Front combination lamp LH
A.
Cut line (R end)
JMLIA1780ZZ
JMLIA1781ZZ
EXL-268
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
FRONT COMBINATION LAMP
NOTE:
After installation, perform aiming adjustment. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст