Nissan Leaf. Manual — part 1283
SYSTEM
WT-11
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
• When ID registration is completed. Refer to
• During the use of the Easy Fill tire alert function.
HORN CONTROL CONDITION
During the use of Easy Fill tire alert function.
Easy Fill Tire Alert Function
INFOID:0000000010120179
• This function operates only when the select lever position is in P-range with the power switch ON or with the
vehicle set to READY.
NOTE:
The Easy Fill tire alert function is recommended to use with the power switch ON.
NOTE:
When beginning tire inflation, it takes a few seconds for the Easy Fill tire alert to function. If there is no
response for approximately 15 seconds or more, cancel the Easy Fill tire alert function and move the vehicle
approximately 1 m (3.2 ft) backward or forward to try again.
• The Easy Fill tire alert function operates only when the select lever position is in P-range with the ignition
switch ON.
• This function informs the driver with a visual and audible indication that the recommended COLD tire pres-
sure has been reached.
• The hazard warning lamps blink when the recommended COLD
tire pressure has been reached. After the recommended COLD tire
pressure has been reached, the horn sounds once and the hazard
warning lamps stop blinking.
• If the tire pressure value is equal to or greater than 30 kPa (0.31
kg/cm
2
, 4 psi) more than the recommended COLD tire pressure,
the hazard warning lamps flash and horn sounds three times.
• To return the tire to the recommended COLD tire pressure, deflate
the tire until the horn sounds once and the hazard warning lamps
stop blinking.
JSEIA0214GB
WT-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010383725
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
AIR PRESSURE MONITOR
Direct Diagnostic Mode
Description
Ecu Identification
The BCM part number is displayed.
Self Diagnostic Result
The BCM self diagnostic results are displayed.
Data Monitor
The BCM input/output data is displayed in real time.
Active Test
The BCM activates outputs to test components.
Work support
The settings for BCM functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN Diag Support Mntr
The result of transmit/receive diagnosis of CAN communication is displayed.
System
Sub System
Direct Diagnostic Mode
E
cu
Id
en
tifi
ca
tio
n
Se
lf Di
ag
no
st
ic Re
su
lt
Da
ta
Mo
ni
tor
A
cti
ve
T
est
W
o
rk support
Co
nf
igu
rat
ion
CA
N Diag
Su
pp
ort Mn
tr
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEADLAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
×
Air conditioner
AIR CONDITIONER
×
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
DIAGNOSIS SYSTEM (BCM)
WT-13
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000010383726
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna signal strength
SELF DIAGNOSTIC RESULT
NOTE:
Before performing Self Diagnostic Result, be sure to register the transmitter ID or the actual malfunction may
be different from that displayed on CONSULT.
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Monitor Item [Unit]
Description
AIR PRESS FL [kPa, kg/cm
2
or Psi]
Indicates air pressure of front LH tire.
AIR PRESS FR [kPa, kg/cm
2
or Psi]
Indicates air pressure of front RH tire.
AIR PRESS RR [kPa, kg/cm
2
or Psi]
Indicates air pressure of rear RH tire.
AIR PRESS RL [kPa, kg/cm
2
or Psi]
Indicates air pressure of rear LH tire.
ID REGST FL1 [Done/Yet]
Indicates ID registration status of front LH transmitter.
ID REGST FR1 [Done/Yet]
Indicates ID registration status of front RH transmitter.
ID REGST RR1 [Done/Yet]
Indicates ID registration status of rear RH transmitter.
ID REGST RL1 [Done/Yet]
Indicates ID registration status of rear LH transmitter.
WARNING LAMP [Off/On]
Indicates condition of low tire pressure warning lamp in combination meter.
Test Item
Description
HORN
This test is able to check horn operation [On].
FLASHER
This test is able to check turn signal lamp operation [RH/LH/Off].
WARNING LAMP
This test is able to check tire pressure warning lamp operation [Off/On].
Support Item
Description
ID READ
Registered ID number of the wheel transmitters is displayed.
ID REGIST
Wheel transmitter ID registration procedure. Refer to
.
WT-14
< ECU DIAGNOSIS INFORMATION >
BCM
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference
INFOID:0000000010120182
ECU
Reference
BCM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст