Nissan Leaf. Manual — part 1166
TM-70
< DTC/CIRCUIT DIAGNOSIS >
[ELECTRIC SHIFT]
P0705 TRANSMISSION RANGE SENSOR A
5. Check the continuity VCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> Replace the electric shift sensor. Refer to
.
NO
>> Repair or replace damaged parts.
Electric shift sensor
VCM
Electric shift sensor
Continuity
Connector
terminal
Connector
terminal
1
E61
17
M57
11
Existed
3
16
10
5
3
9
2
E62
84
5
4
85
3
6
86
4
Electric shift sensor
VCM
Ground
Continuity
Connector
terminal
1
E61
17
Ground
Not existed
3
16
5
3
2
E62
84
4
85
6
86
P0706 TRANSMISSION RANGE SENSOR A
TM-71
< DTC/CIRCUIT DIAGNOSIS >
[ELECTRIC SHIFT]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0706 TRANSMISSION RANGE SENSOR A
DTC Logic
INFOID:0000000010119577
DTC DETECTION LOGIC
Position Pattern Table
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, power switch OFF and wait for at least
10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1. Set the vehicle to READY.
2. Select “Data Monitor” in “SHIFT”.
3. Select “RANGE POSITION”.
4. Shift the selector lever as follows. (Hold the selector lever at each position for 2 seconds or more.)
-
H
→ N → R → N → D → N → H
5. Repeat step 4 five more times.
6. Check DTC.
Is “P0706” detected?
YES
>> Go to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-53, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010119578
1.
CHECK ELECTRIC SHIFT SENSOR INPUT SIGNAL
With CONSULT
1. Set the vehicle to READY.
2. Select “Data Monitor” in “SHIFT”.
3. Select “SHIFT SENSOR 1”, “SHIFT SENSOR 2”, “SHIFT SENSOR 3”, “SHIFT SENSOR 4”, “SHIFT SEN-
SOR 5”, and “SHIFT SENSOR 6”.
4. Operate the selector lever to identify a electric shift sensor of which value does not change.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
P0706
TRANSMISSION RANGE SENSOR A
(Transmission range sensor “A” Circuit
Range/Performance)
Two or more sensors out of electric
shift sensors No. 1 to No. 6 are stuck
at ON or OFF.
• Electric shift sensor
• Harness or connectors
(Each circuit is open or shorted.)
Electric shift control module
recognition position
Selector lever position
Electric shift sensor
No. 1
No. 2
No. 3
No. 4
No. 5
No. 6
H
H
OFF
OFF
ON
OFF
OFF
ON
P
H
OFF
OFF
ON
OFF
OFF
ON
R
R
ON
ON
OFF
OFF
OFF
OFF
N
N
OFF
ON
ON
ON
OFF
OFF
D
D
OFF
OFF
OFF
ON
ON
OFF
Monitor item
Condition
Value / Status
SHIFT SENSOR 1
Selector lever is held in R position
ON
Other than the above
OFF
TM-72
< DTC/CIRCUIT DIAGNOSIS >
[ELECTRIC SHIFT]
P0706 TRANSMISSION RANGE SENSOR A
Without CONSULT
1. Set the vehicle to READY.
2. Operate the selector lever.
3. Check the voltage between VCM vehicle side harness connector terminal and ground.
>> GO TO 2.
2.
CHECK HARNESS BETWEEN VCM AND ELECTRIC SHIFT SENSOR
1. Power switch OFF.
2. Disconnect the VCM connector.
3. Disconnect the electric shift sensor connector.
4. Check the continuity between the malfunctioning electric shift sensor identified at Step 1 and the harness
connector terminal located on the vehicle side of the VCM.
SHIFT SENSOR 2
Selector lever is held in R and N positions
ON
Other than the above
OFF
SHIFT SENSOR 3
Selector lever is held in H (Home) and N positions
ON
Other than the above
OFF
SHIFT SENSOR 4
Selector lever is held in N and D positions
ON
Other than the above
OFF
SHIFT SENSOR 5
Selector lever is held in D position
ON
Other than the above
OFF
SHIFT SENSOR 6
Selector lever in H (Home) position
ON
Other than the above
OFF
Monitor item
Condition
Value / Status
Electric
shift sen-
sor
VCM
Ground
Condition
Voltage
(Approx.)
Connector
terminal
1
E61
17
Ground
Selector lever is held in R position
0 V
Other than the above
5 V
3
16
Selector lever is held in H (Home) and N posi-
tions
0 V
Other than the above
5 V
5
3
Selector lever is held in D position
0 V
Other than the above
5 V
2
E62
84
Selector lever is held in R and N positions
0 V
Other than the above
5 V
4
85
Selector lever is held in N and D position
0 V
Other than the above
5 V
6
86
Selector lever in H (Home) position
0 V
Other than the above
5 V
P0706 TRANSMISSION RANGE SENSOR A
TM-73
< DTC/CIRCUIT DIAGNOSIS >
[ELECTRIC SHIFT]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5. Check the continuity VCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> Replace the electric shift sensor. Refer to
.
NO
>> Repair or replace damaged parts.
Electric shift sensor
VCM
Electric shift sensor
Continuity
Connector
terminal
Connector
terminal
1
E61
17
M57
11
Existed
3
16
10
5
3
9
2
E62
84
5
4
85
3
6
86
4
Electric shift sensor
VCM
Ground
Continuity
Connector
terminal
1
E61
17
Ground
Not existed
3
16
5
3
2
E62
84
4
85
6
86
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст