Nissan Leaf. Manual — part 1135
ST-32
< SYMPTOM DIAGNOSIS >
[WITH HEATED STEERING WHEEL]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
×: Applicable
Symptom
Steering
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
STEERING WHEEL
ST-33
< PERIODIC MAINTENANCE >
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
PERIODIC MAINTENANCE
STEERING WHEEL
Inspection
INFOID:0000000010119098
STEERING WHEEL AXIAL END PLAY
1. Check installation conditions of steering gear assembly, front suspension assembly, axle and steering col-
umn assembly.
2. Check if movement exists when steering wheel is moved up and down, to the left and right and to the axial
direction.
3. Check the following items when steering wheel axial end play is out of the standard.
• Check the steering column assembly mounting condition. Refer to
• Check steering gear assembly mounting condition for looseness. Refer to
STEERING WHEEL PLAY
1. Turn steering wheel so that front wheels come to the straight-ahead position.
2. Set the vehicle to READY and lightly turn steering wheel to the left and right until front wheels start to
move.
3. Measure steering wheel movement on the outer circumference.
4. Check the following items when steering wheel play is out of the standard.
• Check backlash for each joint of steering column assembly.
• Check installation condition of steering gear assembly.
Steering wheel axial end play : Refer to
.
Steering wheel play on the
outer circumference
: Refer to
.
ST-34
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
STEERING WHEEL
REMOVAL AND INSTALLATION
STEERING WHEEL
Exploded View
INFOID:0000000010119099
Removal and Installation
INFOID:0000000010119100
REMOVAL
NOTE:
When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This
will omit neutral position alignment procedure during spiral cable installation.
1. Set vehicle to the straight-ahead position.
2. Remove driver air bag module. Refer to
SR-20, "Removal and Installation"
.
3. Remove heated steering wheel harness connector.
4. Remove steering wheel lock nut after steering is locked.
5. Remove steering wheel using suitable tool (A).
CAUTION:
Place a piece of tape across the spiral cable so it will not be
rotated out of position.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Check the spiral cable neutral position after replacing or rotating spiral cable. Refer to
.
CAUTION:
Never twist spiral cable excessively after it becomes tight. (Twisting may cause the cable to be torn
off.)
• Never reuse steering wheel lock nut.
1.
Steering wheel
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSGIA0704GB
SGIA1524J
STEERING COLUMN
ST-35
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING COLUMN
Exploded View
INFOID:0000000010119101
Removal and Installation
INFOID:0000000010119102
REMOVAL
CAUTION:
• While removing the steering column assembly, do not unlock the tilt lever.
• Do not impact on the axis when removing steering column assembly.
• Be careful when removing steering column assembly from the vehicle because it is heavy.
• Keep steering column assembly away from magnetic sources.
• Do not disassemble steering column assembly. It is not separable.
• While removing the steering column assembly, do not move the steering gear.
• When removing the steering column assembly, be careful not to allow the intermediate shaft to turn.
1. Set vehicle to the straight-ahead position.
2. Place the tilt to the lowest level.
CAUTION:
Securely lock the tilt lever.
3. Remove instrument lower panel LH. Refer to
IP-17, "Removal and Installation"
4. Remove driver air bag module. Refer to
SR-20, "Removal and Installation"
.
5. Remove steering wheel. Refer to
ST-34, "Removal and Installation"
.
6. Remove steering column cover. Refer to
IP-17, "Removal and Installation"
7. Remove spiral cable. Refer to
SR-23, "Removal and Installation"
.
8. Remove combination switch. Refer to
BCS-73, "Removal and Installation"
9. Remove knee protector.
10. Disconnect each switch harness connectors installed to steering column assembly.
1.
Cover
2.
Sub-harness
3.
Band
4.
Steering column assembly
5.
Slide plate (inner)
6.
Slide plate (outer)
7.
Bracket
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSGIA0898GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст