Nissan Leaf. Manual — part 996
PCS
POWER SWITCH POSITION INDICATOR
PCS-67
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Is the inspection normal?
YES
>> Replace BCM. Refer to
BCS-72, "Removal and Installation"
NO
>> Replace power switch. Refer to
PCS-71, "Removal and Installation"
.
Power switch
Ground
Voltage
(Approx.)
Connector
Terminal
M33
7
—
Battery voltage
PCS-68
< SYMPTOM DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
POWER SWITCH DOES NOT OPERATE
SYMPTOM DIAGNOSIS
POWER SWITCH DOES NOT OPERATE
Description
INFOID:0000000010120339
The power switch position does not change even if the power switch (push switch) is operated.
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
NOTE:
The READY set function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelligent
Key system are closely related to each other regarding control. The vehicle security function can operate only
when the door lock and power distribution system are operating normally.
Conditions of Vehicle (Operating Conditions)
• ENGINE START BY I-KEY in WORK SUPPORT is set to On in CONSULT.
• One or more Intelligent Key with registered ID is in the vehicle.
Diagnosis Procedure
INFOID:0000000010120340
1.
PERFORM WORK SUPPORT
Perform INSIDE ANT DIAGNOSIS in Work Support of INTELLIGENT KEY.
PCS-38, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS RESULT
Perform Self Diagnostic Result of BCM.
Is DTC detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
CHECK POWER SWITCH (PUSH SWITCH)
Check power switch (push switch).
PCS-64, "Component Function Check"
Is the operation normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES
>> Refer to
GI-53, "Intermittent Incident"
.
NO
>> GO TO 1.
PCS
POWER SWITCH POSITION INDICATOR DOES NOT ILLUMINATE
PCS-69
< SYMPTOM DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER SWITCH POSITION INDICATOR DOES NOT ILLUMINATE
Description
INFOID:0000000010120341
• Before performing the diagnosis in the following table, check Work Flow. Refer to
• Check that vehicle is under the condition shown in Conditions of vehicle before starting diagnosis, and check
each symptom.
Conditions of Vehicle (Operating Conditions)
• ENGINE START BY I-KEY in WORK SUPPORT is On in CONSULT.
• One or more Intelligent Key with registered ID is in the vehicle.
Diagnosis Procedure
INFOID:0000000010120342
1.
CHECK POWER SWITCH POSITION INDICATOR
Check power switch position indicator.
PCS-66, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Refer to
GI-53, "Intermittent Incident"
.
NO
>> GO TO 1.
PCS-70
< REMOVAL AND INSTALLATION >
[POWER DISTRIBUTION SYSTEM]
NATS ANTENNA AMP.
REMOVAL AND INSTALLATION
NATS ANTENNA AMP.
Removal and Installation
INFOID:0000000010120343
REMOVAL
1. Remove instrument lower panel LH. Refer to
2. Remove the NATS antenna amp.
1. Disengage the NATS antenna amp. (1) fixing pawls using
remover tool etc.
2. Pull NATS antenna amp. to remove it from power switch (2).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA6356ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст