Nissan Leaf. Manual — part 1292
TRANSMITTER
WT-47
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
TRANSMITTER
Exploded View
INFOID:0000000010120217
Removal and Installation
INFOID:0000000010120218
REMOVAL
1. Remove wheel and tire using power tool. Refer to
WT-45, "Removal and Installation"
2. Remove valve cap and valve core to deflate the tire.
NOTE:
If the tire is to be reused, apply a matching mark on the tire in line with the position of the valve stem
assembly for the purpose of wheel and tire balance adjustment after installation.
3. Remove the valve stem nut and allow transmitter to fall into tire.
4. Lubricate the tire outside bead well with a suitable non-silicone lubricant, and remove outside of tire from
the wheel. Reach inside the tire and remove the transmitter.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.
• Be sure not to damage the wheel or transmitter.
• Do not allow lubricant to make contact with transmitter.
5. Lubricate the tire inside bead well with a suitable non-silicone lubricant, and remove inside of tire from the
wheel.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.
1.
Transmitter (tire pressure sensor)
2.
O-ring
3.
Valve stem nut
4.
Valve core
5.
Valve cap
6.
Valve stem assembly
:
Parts that are replaced as a set when the tire is replaced.
AWEIA0212GB
SEIA0047E
WT-48
< REMOVAL AND INSTALLATION >
TRANSMITTER
• Be sure not to damage the wheel.
6. Remove the valve stem from the transmitter as shown.
INSTALLATION
1. Apply a suitable non-silicone lubricant to the tire inside bead.
CAUTION:
Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.
2. Install the tire inside bead (1) onto the wheel (2) in the position
shown.
3. Install the valve stem to the transmitter.
4. Install the O-ring to the transmitter.
CAUTION:
• Do not reuse O-ring
• Insert O-ring to the base of the transmitter.
• The base of the valve stem (A) must be positioned in the
groove of the metal plate as shown.
JSEIA0378ZZ
JPEIC0105ZZ
JSEIA0376GB
TRANSMITTER
WT-49
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
5. Install transmitter (1) to wheel while pressing at position (A).
CAUTION:
• Check that O-ring contacts horizontally with wheel.
• Check that the base of the valve stem is positioned in the
groove of the metal plate.
6. Install and tighten the valve stem nut to the specified torque.
CAUTION:
Do not use power tool for installation.
7. Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degrees from mounting/dismounting head.
NOTE:
Do not touch transmitter with mounting head.
8. Apply a suitable non-silicone lubricant to the tire outside bead.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will
deteriorate the tire and wheel.
• Do not allow lubricant to make contact with transmitter.
9. Install the tire outside bead onto the wheel as normal.
NOTE:
If the tire is being reused, align the matching mark applied on
the tire with the position of the wheel valve stem assembly for the purpose of wheel and tire balance
adjustment after installation. Make sure that the tire does not rotate relative to wheel.
10. Install the valve core and inflate tire.
CAUTION:
Do not reuse valve core.
11. Install the valve cap.
CAUTION:
Do not reuse valve cap.
12. Balance the wheel and tire. Refer to
WT-43, "Wheel Balance Adjustment"
.
13. Install wheel and tire in appropriate wheel position on vehicle. Refer to
WT-45, "Removal and Installation"
.
NOTE:
If replacing the transmitter, then transmitter ID registration procedure must be performed. Refer to
.
14. Adjust neutral position of steering angle sensor. Refer to
.
JSEIA0377ZZ
Valve stem nut
tightening torque
: Refer to
WEIA0046E
WT-50
< REMOVAL AND INSTALLATION >
TIRE PRESSURE RECEIVER
TIRE PRESSURE RECEIVER
Removal and Installation
INFOID:0000000010120219
REMOVAL
1. Remove the remote keyless entry receiver. (The tire pressure receiver is incorporated into remote keyless
entry receiver.) Refer to
DLK-209, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст