Nissan Juke (2014 year). Service Repair Manual — part 160
INL-42
< DTC/CIRCUIT DIAGNOSIS >
INTERIOR ROOM LAMP CONTROL CIRCUIT
INTERIOR ROOM LAMP CONTROL CIRCUIT
Description
INFOID:0000000009750799
Controls each interior room lamp (ground side) by PWM signal.
NOTE:
PWM signal control period is approximately 250 Hz (in the gradual brightening/dimming).
Component Function Check
INFOID:0000000009750800
CAUTION:
Before performing the diagnosis, check that the following are normal.
• Interior room lamp power supply
• Map lamp bulb
1.
CHECK INTERIOR ROOM LAMP CONTROL FUNCTION
CONSULT ACTIVE TEST
1.
Switch the map lamp switch to DOOR.
2.
Turn ignition switch ON.
3.
Select “INT LAMP” of BCM (INT LAMP) active test item.
4.
With operating the test items, check that each interior room lamp turns ON/OFF (gradual brightening/dim-
ming).
Does the interior room lamp turns ON/OFF (gradual brightening/dimming)?
YES
>> Interior room lamp control circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009750801
1.
CHECK INTERIOR ROOM LAMP CONTROL OUTPUT
CONSULT ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Remove all the bulbs of map lamp.
3.
Turn ignition switch ON.
4.
Select “INT LAMP” of BCM (INT LAMP) active test item.
5.
With operating the test item, check continuity between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> GO TO 2.
Fixed ON>>GO TO 3.
Fixed OFF>>Replace BCM. Refer to
BCS-90, "Removal and Installation"
2.
CHECK INTERIOR ROOM LAMP CONTROL OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector, map lamp connector.
On
: Interior room lamp gradual brightening
Off
: Interior room lamp gradual dimming
BCM
Ground
Test item
Continuity
Connector
Terminal
M69
63
INT LAMP
On
Existed
Off
Not existed
BCM
Ground
Test item
Continuity
Connector
Terminal
M66
60
INT LAMP
On
Existed
Off
Not existed
Revision: 2013 October
2014 JUKE
INTERIOR ROOM LAMP CONTROL CIRCUIT
INL-43
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
3.
Check continuity between BCM harness connector and map lamp harness connector.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Replace map lamp.Refer to
INL-49, "Removal and Installation"
.
NO
>> Repair or replace harnesses.
3.
CHECK INTERIOR ROOM LAMP CONTROL SHORT CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and map lamp connector.
3.
Check continuity between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
NO
>> Repair or replace harnesses.
BCM
Map lamp
Continuity
Connector
Terminal
Connector
Terminal
M69
63
R4
2
Existed
BCM
Map lamp
Continuity
Connector
Terminal
Connector
Terminal
M66
60
R4
2
Existed
BCM
Ground
Continuity
Connector
Terminal
M69
63
Not existed
BCM
Ground
Continuity
Connector
Terminal
M66
60
Not existed
Revision: 2013 October
2014 JUKE
INL-44
< DTC/CIRCUIT DIAGNOSIS >
LUGGAGE ROOM LAMP CIRCUIT
LUGGAGE ROOM LAMP CIRCUIT
Description
INFOID:0000000009750802
Controls the luggage room lamp (ground side) to turn the luggage room lamp ON and OFF.
Diagnosis Procedure
INFOID:0000000009750803
CAUTION:
Before performing the diagnosis, check that the following are normal.
• Interior room lamp power supply
• Luggage room lamp bulb
1.
CHECK LUGGAGE ROOM LAMP OUTPUT
1.
Turn ignition switch OFF.
2.
Remove the luggage room lamp bulb.
3.
Check continuity between BCM harness connector and ground.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> GO TO 2.
Fixed ON>>GO TO 3.
Fixed OFF>>Replace BCM. Refer to
BCS-90, "Removal and Installation"
2.
CHECK LUGGAGE ROOM LAMP OPEN CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and luggage room lamp harness connector.
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Replace luggage room lamp.
NO
>> Repair or replace harnesses.
3.
CHECK LUGGAGE ROOM LAMP SHORT CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and ground.
BCM
Ground
Condition
Continuity
Connector
Terminal
B10
49
Back door
Open
Existed
Closed
Not existed
BCM
Ground
Condition
Continuity
Connector
Terminal
B9
55
Back door
Open
Existed
Closed
Not existed
BCM
Luggage room lamp
Continuity
Connector
(+)
Connector
(-)
Terminal
Terminal
B10
49
B11
2
Existed
BCM
Luggage room lamp
Continuity
Connector
(+)
Connector
(-)
Terminal
Terminal
B9
55
B11
2
Existed
Revision: 2013 October
2014 JUKE
LUGGAGE ROOM LAMP CIRCUIT
INL-45
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
With Intelligent Key
Without Intelligent Key
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
NO
>> Repair or replace harnesses.
BCM
Ground
Continuity
Connector
Terminal
B10
49
Not existed
BCM
Ground
Continuity
Connector
Terminal
B9
55
Not existed
Revision: 2013 October
2014 JUKE
INL-46
< DTC/CIRCUIT DIAGNOSIS >
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
Description
INFOID:0000000009750804
Provides the power supply and the ground to control the push-button ignition switch illumination.
Component Function Check
INFOID:0000000009750805
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION
CONSULT ACTIVE TEST
1.
Turn the ignition switch ON.
2.
Select “ENGINE SW ILLUMI” of BCM (INTELLIGENT KEY) active test item.
3.
With operating the test items, check that the push-button ignition switch illumination turns ON/OFF.
Does the push-button ignition switch illumination turn ON/OFF?
YES
>> Push-button ignition switch illumination circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009750806
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OUTPUT
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector.
3.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and the push-button ignition switch harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harnesses.
3.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
On
: Push-button ignition switch illumination ON
Off
: Push-button ignition switch illumination OFF
(+)
(–)
Condition
Voltage
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
5
Ground
Push-button ignition switch
illumination
ON
12 V
OFF
0 V
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M70
90
M101
5
Existed
BCM
Ground
Continuity
Connector
Terminal
M70
90
Not existed
Revision: 2013 October
2014 JUKE
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
INL-47
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
NO
>> Repair or replace harnesses.
4.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace push-button ignition switch.
NO
>> Repair or replace harnesses.
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
6
Existed
Revision: 2013 October
2014 JUKE
INL-48
< SYMPTOM DIAGNOSIS >
INTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000009750807
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Symptom
Possible cause
Inspection item
All the following lamps do not turn ON.
• Map lamp
• Luggage room lamp
• Harness between BCM and each
interior room lamp
• BCM
Interior room lamp power supply cir-
cuit
Refer to
• Interior room lamp does not turn ON even
though the door is open.
(It turns ON when turning the interior room
lamp ON.)
• Interior room lamp does not turn OFF even
though the door is closed.
• Harness between BCM and each
door switch
• Harness between BCM and each
interior room lamp
• BCM
Interior room lamp control circuit
Refer to
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
• Luggage room lamp does not turn ON even
though the back door is open.
• Luggage room lamp does not turn OFF even
though the back door is closed.
• Harness between BCM and back
door switch
• Harness between BCM and lug-
gage room lamp
• BCM
Back door switch circuit
Refer to
Luggage room lamp circuit
Refer to
Push-button ignition switch illumination does not
illuminate.
• Harness between BCM and push-
button ignition switch
• BCM
Push-button ignition switch illumina-
tion circuit
Refer to
Interior room lamp battery saver does not acti-
vate.
BCM
Revision: 2013 October
2014 JUKE
MAP LAMP
INL-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
REMOVAL AND INSTALLATION
MAP LAMP
Exploded View
INFOID:0000000009750808
Removal and Installation
INFOID:0000000009750809
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage.
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens (1).
CAUTION:
• Use a remover tool wrapped in tape.
• Insert a remover tool into the gap between bulb housing
and lens.
2.
Disengage bulb housing (1) fixing pawl using a remover tool (A)
according to numerical order 1
→
2 indicated by the arrows as
shown in the figure.
CAUTION:
Use a remover tool wrapped in tape.
3.
Disconnect map lamp harness connector, and then remove bulb housing.
1.
Bulb housing
2.
Bulb
3.
Lens
: Pawl
JMLIA1062ZZ
: Pawl
JMLIA1063ZZ
: Pawl
JMLIA1064ZZ
Revision: 2013 October
2014 JUKE
INL-50
< REMOVAL AND INSTALLATION >
MAP LAMP
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000009750810
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
MAP LAMP BULB
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens (1).
CAUTION:
• Use a remover tool wrapped in tape.
• Insert a remover tool into the gap between bulb housing
and lens.
2.
Remove bulb.
: Pawl
JMLIA1063ZZ
Revision: 2013 October
2014 JUKE
GLOVE BOX LAMP
INL-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
GLOVE BOX LAMP
Exploded View
INFOID:0000000009750811
Removal and Installation
INFOID:0000000009750812
Replacement
INFOID:0000000009750813
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
GLOVE BOX LAMP BULB
1.
Remove glove box assembly. Refer to
IP-13, "Removal and Installation"
2.
Rotate the bulb & socket assembly counterclockwise and unlock
it, and then remove bulb & socket assembly.
1.
Bulb housing
2.
Bulb & socket assembly
3.
Glove box assembly
: Pawl
: Vehicle front
JMLIA3198ZZ
JMLIA1528ZZ
Revision: 2013 October
2014 JUKE
INL-52
< REMOVAL AND INSTALLATION >
LUGGAGE ROOM LAMP
LUGGAGE ROOM LAMP
Exploded View
INFOID:0000000009750814
Removal and Installation
INFOID:0000000009750815
REMOVAL
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
1.
Disengage luggage room lamp fixing pawl using a remover tool
(A) according to numerical order 1
→
2 indicated by the arrows as
shown in the figure.
CAUTION:
Insert a remover tool into the gap between luggage room
lamp and luggage side lower finisher RH.
2.
Disconnect luggage room lamp harness connector, and then remove luggage room lamp.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000009750816
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
1.
Shade
2.
Bulb
3.
Lens
: Pawl
JMLIA1238ZZ
: Pawl
JMLIA1280ZZ
Revision: 2013 October
2014 JUKE
LUGGAGE ROOM LAMP
INL-53
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
LUGGAGE ROOM LAMP BULB
1.
Remove luggage room lamp. Refer to
INL-52, "Removal and Installation"
2.
Disengage shade fixing pawls using a remover tool (A) accord-
ing to the direction indicated by the arrow as shown in the figure.
CAUTION:
Use remover tool wrapped in tape.
3.
Remove shade, and then remove bulb.
: Pawl
JMLIA1700ZZ
Revision: 2013 October
2014 JUKE
INL-54
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000009750817
*
: With Intelligent Key
Item
Type
Wattage (W)
Push-button ignition switch illumination*
LED
—
Map lamp
W5W
5
Glove box lamp
—
1.4
Luggage room lamp
—
5
Revision: 2013 October
2014 JUKE
INT-1
BODY INTERIOR
C
D
E
F
G
H
I
K
L
M
SECTION
INT
A
B
INT
N
O
P
CONTENTS
INTERIOR
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover
. ..
Precautions for Removing of Battery Terminal . .....
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
CLIP LIST . . . . . . . . . . . . . . .
Clip List . . . . . . . . . . . . . . . . .....
SYMPTOM DIAGNOSIS . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . .
Work Flow . . . . . . . . . . . . . . . .....
Inspection Procedure . . . . . . . . . . . ....
Diagnostic Worksheet . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
FRONT DOOR FINISHER . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REAR DOOR FINISHER . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
BODY SIDE TRIM . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
FRONT PILLAR GARNISH . . . . . . . . . ...
FRONT PILLAR GARNISH : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
KICKING PLATE INNER . . . . . . . . . . ...
KICKING PLATE INNER : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
DASH SIDE FINISHER . . . . . . . . . . . ..
DASH SIDE FINISHER : Removal and Installation
.
BODY SIDE WELT . . . . . . . . . . . . . .
BODY SIDE WELT : Removal and Installation . .
CENTER PILLAR LOWER GARNISH . . . . . ...
CENTER PILLAR LOWER GARNISH : Removal
and Installation . . . . . . . . . . . . . .
CENTER PILLAR UPPER GARNISH . . . . . .
CENTER PILLAR UPPER GARNISH : Removal
and Installation . . . . . . . . . . . . . .
FLOOR TRIM . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
HEADLINING . . . . . . . . . . . . .
NORMAL ROOF . . . . . . . . . . . . . .
NORMAL ROOF : Exploded View . . . . . . ...
NORMAL ROOF : Removal and Installation . . ...
SUNROOF . . . . . . . . . . . . . . . . ..
SUNROOF : Exploded View . . . . . . . . .
SUNROOF : Removal and Installation . . . . .
LUGGAGE FLOOR TRIM . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
LUGGAGE REAR PLATE . . . . . . . . . . .
LUGGAGE REAR PLATE : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
LUGGAGE SIDE LOWER FINISHER . . . . . .
LUGGAGE SIDE LOWER FINISHER : Removal
and Installation . . . . . . . . . . . . . .
Revision: 2013 October
2014 JUKE
INT-2
LUGGAGE SIDE UPPER FINISHER . . . . . ....
LUGGAGE SIDE UPPER FINISHER : Removal
and Installation . . . . . . . . . . . . . ...
BACK DOOR TRIM . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ....
BACK DOOR PULL HANDLE . . . . . . . . ..
BACK DOOR PULL HANDLE : Removal and In-
stallation . . . . . . . . . . . . . . . . .
BACK DOOR LOWER FINISHER . . . . . . . .
BACK DOOR LOWER FINISHER : Removal and
Installation . . . . . . . . . . . . . . . ...
BACK DOOR SIDE FINISHER . . . . . . . . ..
BACK DOOR SIDE FINISHER : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
EMERGENCY LID . . . . . . . . . . . . . .
EMERGENCY LID : Removal and Installation . .
Revision: 2013 October
2014 JUKE
PRECAUTIONS
INT-3
< PRECAUTION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009750118
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009750119
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
PIIB3706J
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст