Nissan Juke (2014 year). Service Repair Manual — part 243
TRANSAXLE ASSEMBLY
TM-33
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Disassembly
INFOID:0000000009752468
1.
Remove drain plug and gasket from clutch housing, using a socket [Commercial service tool] and then
drain gear oil.
2.
Remove filler plug and gasket from transaxle case.
3.
Remove selector lever (1) retaining pin with a pin punch to
remove selector lever.
4.
Remove bracket (2) and position switch (3) from transaxle case.
1.
Shim
2.
Differential side bearing outer race
(transaxle case side)
3.
Differential side bearing inner race
(transaxle case side)
4.
Final gear
5.
Differential case
6.
Differential side bearing inner race
(clutch housing side)
7.
Differential side bearing outer race
(clutch housing side)
: Replace the parts as a set.
: N·m (kg-m, ft-lb)
JPDIC0424GB
PCIB1693E
Revision: 2013 October
2014 JUKE
TM-34
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
5.
Remove transaxle case mounting bolts (
).
6.
Remove reverse idler shaft mounting bolt (
) and seal washer.
7.
Remove transaxle case (2) while rotating shifter lever A (1) in
the direction as shown in the figure.
8.
Remove selector spring (1) from return bushing (A).
9.
Shift 1st-2nd fork rod (1), fork rod (2), and reverse fork rod (3) to
the neutral position.
10. Remove selector (4) from clutch housing.
PCIB1694E
PCIB1695E
JPDIC0444ZZ
JPDIC0445ZZ
PCIB1698E
Revision: 2013 October
2014 JUKE
TRANSAXLE ASSEMBLY
TM-35
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
11. Remove reverse idler shaft assembly (1), as per the following
procedure.
a.
Pull up input shaft assembly (2), mainshaft assembly (3), fork
rod (4), and 1st-2nd fork rod (5).
NOTE:
It is easier to pull up when shifting each fork rod to each shaft
side.
b.
Remove reverse idler shaft assembly and reverse fork rod (6)
from clutch housing.
12. Remove spring washer from clutch housing.
13. Pull up and remove input shaft assembly (1), mainshaft assem-
bly (2), fork rod (3), and 1st-2nd fork rod (4) from clutch housing.
NOTE:
It is easier to pull up when shifting each fork rod to each shaft
side.
14. Remove final drive assembly (1) from clutch housing.
15. Remove magnet from clutch housing.
16. Remove differential side oil seals (1) from clutch housing and
transaxle case.
CAUTION:
Never damage clutch housing and transaxle case.
17. Remove differential side bearing outer race (1) from clutch hous-
ing, using a brass rod.
CAUTION:
Never damage clutch housing.
JPDIC0606ZZ
JPDIC0607ZZ
PCIB1703E
PCIB1704E
PCIB1716E
Revision: 2013 October
2014 JUKE
TM-36
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
18. Remove differential side bearing outer race (1) from transaxle
case, using a brass rod.
CAUTION:
Never damage transaxle case.
19. Remove shim (2) from transaxle case.
20. Remove shifter lever A (1) retaining pin, using a pin punch.
21. Remove shifter lever A from transaxle case.
22. Remove shifter lever B (1) from transaxle case.
23. Remove oil gutter (1) from transaxle case.
24. Remove bushings (1) from transaxle case, using a remover
[Commercial service tool].
PCIB1705E
JPDIC0106ZZ
PCIB1712E
PCIB1707E
PCIB1710E
Revision: 2013 October
2014 JUKE
TRANSAXLE ASSEMBLY
TM-37
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
25. Remove mainshaft rear bearing outer race from transaxle case,
using a remover [Commercial service tool].
26. Remove mainshaft rear bearing adjusting shim from transaxle
case.
27. Remove snap ring (1) and oil channel (2) from transaxle case.
28. Remove input shaft oil seal (1) from clutch housing, using an oil
seal remover.
CAUTION:
Never damage clutch housing.
29. Remove mainshaft front bearing outer race (1) from clutch hous-
ing, using the puller (A) [SST: KV381054S0 (J-34286)] and a
spacer (B) [Commercial service tool].
30. Remove oil channel (2) from clutch housing.
31. Remove bushing (1) from clutch housing, using a remover
[Commercial service tool].
PCIB1706E
PCIB1708E
PCIB1714E
JPDIC0107ZZ
PCIB1717E
Revision: 2013 October
2014 JUKE
TM-38
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
32. Remove 2 way connector (1) from clutch housing.
33. Remove plug from clutch housing.
34. Remove pinion gear (1) and pinion shaft (2) from clutch housing.
Assembly
INFOID:0000000009752469
1.
Install pinion gear (1) and pinion shaft (2) to clutch housing.
CAUTION:
Replace transaxle assembly when replacing clutch hous-
ing.
2.
Install plug to clutch housing.
3.
Install 2 way connector (1) to clutch housing.
PCIB1720E
PCIB1719E
PCIB1719E
PCIB1720E
Revision: 2013 October
2014 JUKE
TRANSAXLE ASSEMBLY
TM-39
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Install bushings (1) so that they becomes even to clutch housing
edge surface, using a drift (A) [Commercial service tool].
5.
Install oil channel to clutch housing.
CAUTION:
Never reuse oil channel.
6.
Install mainshaft front bearing outer race to clutch housing,
using the drift (A) [SST: KV38100200 ( - )].
CAUTION:
Replace mainshaft front bearing outer race and mainshaft
front bearing inner race as a set.
7.
Install input shaft oil seal (1) to clutch housing, using the drift (A)
[SST: ST33220000 ( - )].
8.
Install snap ring (1) and oil channel (2) to transaxle case.
CAUTION:
• Select and install snap ring that has the same thickness
as previous one.
• Replace transaxle assembly when replacing transaxle
case.
9.
Install mainshaft rear bearing adjusting shim to transaxle case.
CAUTION:
Select mainshaft rear bearing adjusting shim, as per the fol-
lowing procedure when replacing mainshaft adjusting
shim, 6th main gear, 5th main gear, or 4th main gear.
• Replace mainshaft adjusting shim.
- If new mainshaft adjusting shim is thinner than previous one, offset the thickness difference by
selecting thicker mainshaft rear bearing adjusting shim.
- If new mainshaft adjusting shim is thicker than previous one, offset the thickness difference by
selecting thinner mainshaft rear bearing adjusting shim.
• Replace 6th main gear, 5th main gear, or 4th main gear.
- Measure the thickness of the main gear used before and the new main gear
- Increase the thickness of the mainshaft rear bearing adjusting shim, if the difference is smaller
than 0.025 mm (0.0010 in).
- Decrease the thickness of the mainshaft rear bearing adjusting shim, if the difference is greater
than 0.025 mm (0.0010 in).
JPDIC0108ZZ
PCIB1724E
PCIB1721E
PCIB1729E
Revision: 2013 October
2014 JUKE
TM-40
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
10. Install mainshaft rear bearing outer race to transaxle case, using
the drift (A) [SST: KV38100200 ( - )].
CAUTION:
Replace mainshaft rear bearing outer race and mainshaft
rear bearing inner race as a set.
11. Install bushings (1) to transaxle case, using a drift (A) [Commer-
cial service tool].
12. Install oil gutter (1) to transaxle case.
13. Install shifter lever B (1) to transaxle case.
CAUTION:
Replace shifter lever A and shifter lever B as a set.
14. Install shifter lever A to transaxle case.
CAUTION:
Replace shifter lever A and shifter lever B as a set.
15. Install retaining pin to shifter lever A (1), using a pin punch.
CAUTION:
Never reuse retaining pin.
16. Install shim to transaxle case.
PCIB1728E
JPDIC0109ZZ
PCIB1730E
PCIB1712E
BCIA0047E
Revision: 2013 October
2014 JUKE
TRANSAXLE ASSEMBLY
TM-41
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
17. Install differential side bearing outer race (transaxle case side)
to transaxle case, using the drift (A) [SST: ST33400001 (J-
26082)].
CAUTION:
Replace differential side bearing outer race (transaxle case
side) and differential side bearing inner race (transaxle case
side) as a set.
18. Install differential side bearing outer race (clutch housing side) to
clutch housing, using the drift (A) [SST: KV38100200 ( - )].
CAUTION:
Replace differential side bearing outer race (clutch housing
side) and differential side bearing inner race (clutch hous-
ing side) as a set.
19. Install differential side oil seals (1) to clutch housing and tran-
saxle case, using the drift [Stamping number: B.vi 1666-B] of the
drift set [SST: KV32500QAA ( - )].
CAUTION:
• Never incline differential side oil seal.
• Never damage clutch housing and transaxle case.
20. Install magnet to clutch housing.
21. Install final drive assembly to clutch housing.
22. Set fork rod (1) to input shaft assembly (2), and then install them
to clutch housing.
PCIB1726E
PCIB1722E
A
: Transaxle case side
B
: Clutch housing side
Dimension “L
1
”
: 1.2 – 1.8 mm (0.047 – 0.071 in)
Dimension “L
2
”
: 2.7 – 3.3 mm (0.106 – 0.130 in)
JPDIC0454ZZ
JPDIC0608ZZ
Revision: 2013 October
2014 JUKE
TM-42
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
23. Install mainshaft assembly (1), as per the following procedure.
a.
Pull up input shaft assembly (2) and fork rod (3).
b.
Set 1st-2nd fork rod (4) to mainshaft assembly, and then install
them to clutch housing.
24. Install reverse idler shaft assembly (1), as per the following pro-
cedure.
a.
Install spring washer to clutch housing.
b.
Pull up input shaft assembly (2), mainshaft assembly (3), fork
rod (4), and 1st-2nd fork rod (5).
NOTE:
It is easier to pull up when shifting each fork rod to each shaft
side.
c.
Set reverse fork rod (6) to reverse idler shaft assembly, and then
install them to clutch housing.
25. Shift 1st-2nd fork rod (1), fork rod (2), and reverse fork rod (3) to
the neutral position.
26. Install selector (4) to clutch housing.
CAUTION:
Replace selector lever and selector as a set.
27. Install selector spring (1) to return bushing (A).
28. Apply recommended sealant to mounting surface of transaxle
case.
• Use Genuine Silicone RTV or an equivalent. Refer to
24, "Recommended Chemical Products and Sealants"
.
CAUTION:
• Never allow old liquid gasket, moisture, oil, or foreign
matter to remain on mounting surface.
• Check that mounting surface is not damaged.
• Apply sealant bead continuously.
29. Install transaxle case to clutch housing while rotating shifter
lever A (1) in the direction as shown in the figure.
JPDIC0609ZZ
JPDIC0606ZZ
SCIA7782E
JPDIC0445ZZ
JPDIC0110ZZ
Revision: 2013 October
2014 JUKE
TRANSAXLE ASSEMBLY
TM-43
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
30. Install reverse idler shaft mounting bolt (
), as per the following
procedure.
a.
Install seal washer to reverse idler shaft mounting bolt, and
install reverse idler shaft mounting bolt to transaxle case.
CAUTION:
Never reuse seal washer.
b.
Tighten reverse idler shaft mounting bolt to the specified torque.
31. Tighten transaxle case mounting bolts (
) to the specified
torque.
32. Install position switch (1), as per the following procedure.
a.
Apply recommended sealant to threads of position switch.
• Use Genuine Silicone RTV or an equivalent. Refer to
24, "Recommended Chemical Products and Sealants"
.
CAUTION:
Never allow old liquid gasket, moisture, oil, or foreign mat-
ter to remain on thread.
b.
Install position switch to transaxle case, and tighten it to the
specified torque.
33. Install bracket (2) to transaxle case, and tighten mounting bolt to
the specified torque.
34. Install selector lever (3), as per the following procedure.
a.
Install selector lever to transaxle case.
CAUTION:
Replace selector lever and selector as a set.
b.
Install retaining pin to selector lever, using a pin punch.
CAUTION:
Never reuse retaining pin.
35. Install drain plug, as per the following procedure.
a.
Install gasket to drain plug.
CAUTION:
Never reuse gasket.
b.
Install drain plug to clutch housing, using a socket [Commercial service tool].
c.
Tighten drain plug to the specified torque.
36. Install filler plug, as per the following procedure.
a.
Install gasket to filler plug, and then install them to transaxle case.
CAUTION:
Never reuse gasket.
b.
Tighten filler plug to the specified torque.
CAUTION:
Fill with gear oil before tighten filler plug to the specified torque.
PCIB1695E
PCIB1694E
SCIA7784E
Revision: 2013 October
2014 JUKE
TM-44
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
Inspection
INFOID:0000000009752470
INSPECTION AFTER DISASSEMBLY
Check contact surface and sliding surface for excessive wear,
uneven wear, bend, and damage. Replace if necessary.
SCIA7785E
Revision: 2013 October
2014 JUKE
INPUT SHAFT AND GEAR
TM-45
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
INPUT SHAFT AND GEAR
Exploded View
INFOID:0000000009752471
Disassembly
INFOID:0000000009752472
CAUTION:
1.
Input shaft front bearing
2.
Input shaft
3.
3rd input gear
4.
Spacer
5.
Snap ring
6.
3rd baulk ring
7.
3rd-4th coupling sleeve
8.
3rd-4th synchronizer hub
9.
Insert key
10. 4th baulk ring
11. 4th input gear
12. 5th input gear
13. 5th baulk ring
14. 5th-6th coupling sleeve
15. 5th-6th synchronizer hub
16. 6th baulk ring
17. Needle bearing
18. 6th input gear
19. Input shaft rear bearing
A.
First step
B.
Final step
: Apply gear oil.
: Replace the parts as a set.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPDIC0407GB
Revision: 2013 October
2014 JUKE
TM-46
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
INPUT SHAFT AND GEAR
• Fix input shaft in a vise with back plate, and then remove gears and snap rings.
• For removal of snap ring, set snap ring pliers and flat pliers at
both sides of snap ring. While expanding snap ring with snap
ring pliers, move snap ring with flat pliers.
• Disassemble gear components putting direction marks on the
parts that do not affect any functions.
1.
Remove input shaft rear bearing mounting bolt (1), using the
drift (A) [SST: KV32300QAM ( - )].
2.
Remove input shaft rear bearing (1), as per the following proce-
dure.
a.
Set a puller [Commercial service tool] to input shaft rear bearing.
b.
Remove input shaft rear bearing, using a drift (A) [Commercial
service tool].
3.
Remove spacer (1), 6th input gear (2), needle bearing, 6th baulk
ring, and 5th-6th synchronizer hub assembly (3).
4.
Remove insert keys and 5th-6th coupling sleeve from 5th-6th
synchronizer hub.
SCIA1755J
JPDIC0449ZZ
JPDIC0111ZZ
PCIB1750E
Revision: 2013 October
2014 JUKE
INPUT SHAFT AND GEAR
TM-47
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5.
Remove snap ring (1).
6.
Remove spacer, 5th baulk ring, 5th input gear (2), and spacer.
7.
Remove snap ring (1).
8.
Remove spacer, 4th input gear (2), 4th baulk ring, and 3rd-4th
synchronizer hub assembly (3).
9.
Remove insert keys and 3rd-4th coupling sleeve from 3rd-4th
synchronizer hub.
10. Remove snap ring (1).
11. Remove spacer, 3rd baulk ring, and 3rd input gear (2).
12. Set a puller [Commercial service tool] to input shaft front bearing
(1), and then remove input shaft front bearing.
Assembly
INFOID:0000000009752473
Note the following procedures, and assemble in the reverse order of disassembly.
CAUTION:
• Replace transaxle assembly when replacing input shaft.
PCIB1754E
PCIB1753E
PCIB1752E
PCIB1751E
Revision: 2013 October
2014 JUKE
TM-48
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
INPUT SHAFT AND GEAR
• For installation of snap ring, set snap ring pliers and flat pliers
at both sides of snap ring. While expanding snap ring with
snap ring pliers, move snap ring with flat pliers.
• Never reuse snap ring.
• Check that snap ring is securely installed in a groove.
• Replace 3rd-4th coupling sleeve and 3rd-4th synchronizer
hub as a set.
• Replace 5th-6th coupling sleeve and 5th-6th synchronizer hub
as a set.
• Be careful to install 3rd-4th synchronizer hub according to the
specified direction.
• Be careful to install 5th-6th synchronizer hub according to the
specified direction.
• Install input shaft front bearing (1), using a drift (A) [Commercial
service tool].
SCIA1755J
A : 3rd input gear side
B : 4th input gear side
PCIB1748E
A : 5th input gear side
B : 6th input gear side
PCIB1749E
JPDIC0112ZZ
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст