Nissan Juke (2014 year). Service Repair Manual — part 266
WCS
WARNING CHIME SYSTEM
WCS-35
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
JRNWD0688GB
Revision: 2013 October
2014 JUKE
WCS-36
< WIRING DIAGRAM >
WARNING CHIME SYSTEM
JRNWD0689GB
Revision: 2013 October
2014 JUKE
WCS
DIAGNOSIS AND REPAIR WORKFLOW
WCS-37
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000009752252
OVERALL SEQUENCE
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2.
CHECK SYMPTOM
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.
CHECK CONSULT SELF-DIAGNOSIS RESULTS
1.
Connect CONSULT and perform self-diagnosis. Refer to
WCS-19, "BUZZER : CONSULT Function (BCM
(with intelligent key system) or
WCS-21, "BUZZER : CONSULT Function (BCM - BUZZER)"
(without intelligent key system).
2.
When DTC is detected, follow the instructions below:
-
Record DTC and Freeze Frame Data.
Are self-diagnosis results normal?
YES
>> GO TO 4.
JSNIA4492GB
Revision: 2013 October
2014 JUKE
WCS-38
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
NO
>> GO TO 5.
4.
NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts.
>> GO TO 5.
5.
REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES
>> INSPECTION END
NO
>> GO TO 1.
Revision: 2013 October
2014 JUKE
WCS
POWER SUPPLY AND GROUND CIRCUIT
WCS-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure
INFOID:0000000010318436
1.
CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Be sure to eliminate cause of malfunction before installing new fuse.
2.
CHECK POWER SUPPLY CIRCUIT
Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check harness between combination meter and fuse.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector.
3.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Power source
Fuse No.
Battery
13
Ignition switch ON or START
5
Ignition switch ACC or ON
Without intelligent key
18
With intelligent key
19
Terminals
Ignition switch po-
sition
Voltage
(Approx.)
(+)
(
−
)
Combination meter
Ground
Connector
Terminal
M34
27
OFF
Battery voltage
15
ACC
28
ON
Combination meter
Ground
Continuity
Connector
Terminal
M34
21
Existed
22
23
25
Revision: 2013 October
2014 JUKE
WCS-40
< DTC/CIRCUIT DIAGNOSIS >
METER BUZZER CIRCUIT
METER BUZZER CIRCUIT
Component Function Check
INFOID:0000000009752254
1.
CHECK OPERATION OF METER BUZZER
1.
Select “BUZZER” of “BCM” on CONSULT.
2.
Perform “LIGHT WARN ALM” of “Active Test”.
Does meter buzzer beep?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
or
BCS-157, "Removal and Installation"
(WITHOUT INTELLIGENT KEY SYSTEM).
Diagnosis Procedure
INFOID:0000000009752255
1.
CHECK POWER SUPPLY OF COMBINATION METER
Check power supply of combination meter. Refer to
WCS-39, "COMBINATION METER : Diagnosis Proce-
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair power supply circuit of combination meter.
BUZZER
Under the condition of buzzer input
: On
Except above
: Off
Revision: 2013 October
2014 JUKE
WCS
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
WCS-41
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
Component Function Check
INFOID:0000000009752256
1.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUCKLE SW” monitor value.
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009752257
1.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and seat belt buckle switch (driver side) connector.
3.
Check continuity between combination meter harness connector and seat belt buckle switch (driver side)
harness connector.
4.
Check harness continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) GROUND CIRCUIT
Check harness continuity between seat belt buckle switch (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000009752258
1.
CHECK SEAT BELT BUCKLE SWITCH UNIT
1.
Turn ignition switch OFF.
2.
Disconnect the seat belt buckle switch (driver side) connector.
3.
Check continuity between terminals.
BUCKLE SW
When driver seat belt is fastened
: Off
When driver seat belt is unfastened
: On
Combination meter
Seat belt buckle switch (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M34
9
B50
1
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M34
9
Not existed
Seat belt buckle switch (driver side)
Ground
Continuity
Connector
Terminal
B50
2
Existed
Revision: 2013 October
2014 JUKE
WCS-42
< DTC/CIRCUIT DIAGNOSIS >
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the seat belt buckle (driver side). Refer to
SB-8, "SEAT BELT BUCKLE : Removal and
Terminal
Condition
Continuity
1
2
When driver seat belt is fastened
Not existed
When driver seat belt is unfastened
Existed
Revision: 2013 October
2014 JUKE
WCS
PARKING BRAKE SWITCH SIGNAL CIRCUIT
WCS-43
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PARKING BRAKE SWITCH SIGNAL CIRCUIT
Diagnosis Procedure
INFOID:0000000009752259
1.
CHECK COMBINATION METER INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check the voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and parking brake switch connector.
3.
Check continuity between combination meter harness connector and parking brake switch harness con-
nector.
4.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000009752260
1.
CHECK PARKING BRAKE SWITCH
Check parking brake switch. Refer to
BRC-117, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace parking brake switch. Refer to
.
(+)
(
−
)
Condition
Voltage
(Approx.)
Combination meter
Ground
Connector
Terminal
M34
10
Ignition
switch ON
When parking brake is applied
0 V
When parking brake is released
12 V
Terminals
Continuity
Combination meter
Parking brake switch
Connector
Terminal
Connector
Terminal
M34
10
M31
1
Existed
Terminals
Continuity
Combination meter
Ground
Connector
Terminal
M34
10
Not existed
Revision: 2013 October
2014 JUKE
WCS-44
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
SYMPTOM DIAGNOSIS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description
INFOID:0000000009752261
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure
INFOID:0000000009752262
1.
CHECK PARKING BRAKE WARNING LAMP
1.
Start the engine.
2.
Check the operation of the brake warning lamp by operating the parking brake.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-61, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Perform check for the parking brake switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK PARKING BRAKE SWITCH
Perform a unit check for the parking brake switch. Refer to
WCS-43, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-61, "Removal and Installation"
NO
>> Replace parking brake switch. Refer to
.
When parking brake is applied
: ON
When parking brake is released
: OFF
Revision: 2013 October
2014 JUKE
WCS
THE LIGHT REMINDER WARNING DOES NOT SOUND
WCS-45
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description
INFOID:0000000009752263
Light reminder warning chime does not sound even though headlamp is illuminated.
Diagnosis Procedure
INFOID:0000000009752264
1.
CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION
Check that the headlamps operate normally by operating the combination switch (lighting switch).
Do they operate normally?
YES
>> GO TO 2.
NO
>> Refer to
EXL-82, "WITH DAYTIME RUNNING LIGHT SYSTEM : Symptom Table"
(WITH DAY-
TIME RUNNING LIGHT SYSTEM) or
EXL-81, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM
(WITHOUT DAYTIME RUNNING LIGHT SYSTEM).
2.
CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT
Perform the check for the driver side door switch signal circuit. Refer to
(WITH
INTELLIGENT KEY SYSTEM ) or
DLK-220, "Diagnosis Procedure"
(WITHOUT INTELLIGENT KEY SYS-
TEM).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK DRIVER SIDE DOOR SWITCH
Perform a unit check for the driver side door switch. Refer to
DLK-82, "Component Inspection"
(WITH INTEL-
LIGENT KEY SYSTEM ) or
DLK-221, "Component Inspection"
(WITHOUT INTELLIGENT KEY SYSTEM).
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
or
BCS-157, "Removal and Installation"
(WITHOUT INTELLIGENT KEY SYSTEM).
NO
>> Replace driver side door switch. Refer to
DLK-172, "Removal and Installation"
(WITH INTELLI-
GENT KEY SYSTEM ) or
DLK-295, "Removal and Installation"
(WITHOUT INTELLIGENT KEY
SYSTEM).
Revision: 2013 October
2014 JUKE
WCS-46
< SYMPTOM DIAGNOSIS >
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
SOUND
Description
INFOID:0000000009752265
• Seat belt warning does not sound.
• Seat belt warning sounds continuously.
Diagnosis Procedure
INFOID:0000000009752266
1.
CHECK SEAT BELT WARNING LAMP
1.
Turn ignition switch ON.
2.
Check the operation of the seat belt warning lamp in the combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK BCM OUTPUT SIGNAL
Check if the seat belt warning chime is activated by performing BCM active test. Refer to
CONSULT Function (BCM - BUZZER)"
(WITH INTELLIGENT KEY SYSTEM) or
(WITHOUT INTELLIGENT KEY SYSTEM).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT SIGNAL
Check if buzzer switches to proper condition (On/Off) on data monitor of combination meter. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-61, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
or
BCS-157, "Removal and Installation"
(WITHOUT INTELLIGENT KEY SYSTEM).
4.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT
Perform the check for the seat belt buckle switch (driver side) circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform a unit check for the seat belt buckle switch (driver side). Refer to
WCS-41, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-61, "Removal and Installation"
NO
>> Replace seat belt buckle (driver side). Refer to
SB-8, "SEAT BELT BUCKLE : Removal and Instal-
.
Seat belt fastened
: OFF
Seat belt not fastened
: ON
Buzzer active condition
: On
Buzzer non-active condition
: Off
Revision: 2013 October
2014 JUKE
WCS
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
WCS-47
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
Description
INFOID:0000000009752267
The key warning chime does not sound, when all of the following conditions are fulfilled.
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in ACC or OFF (ignition switch signal OFF).
• Driver side door is open (driver side door switch ON)
Diagnosis Procedure
INFOID:0000000009752268
1.
CHECK BCM INPUT SIGNAL
1.
Connect CONSULT.
2.
Select the “Data Monitor” of “BCM (BUZZER)” and check the “KEY ON SW” monitor value. Refer to
19, "BUZZER : CONSULT Function (BCM - BUZZER)"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-157, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK KEY SWITCH SIGNAL CIRCUIT
Check the key switch signal circuit. Refer to
DLK-224, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-157, "Removal and Installation"
.
NO
>> Check applicable parts, and repair or replace corresponding parts.
Revision: 2013 October
2014 JUKE
WT-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
WT
A
B
WT
N
O
P
CONTENTS
ROAD WHEELS & TIRES
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing of Battery Terminal . .....
Service Notice and Precautions for TPMS . . . ....
Service Notice and Precautions for Road Wheel ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
BCM . . . . . . . . . . . . . . . . . . ..
Tire Pressure Sensor . . . . . . . . . . . ....
Tire Pressure Receiver . . . . . . . . . . .....
Information Display . . . . . . . . . . . . ...
SYSTEM . . . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) . . . . . . . . . . ..
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
AIR PRESSURE MONITOR . . . . . . . . . ..
AIR PRESSURE MONITOR : CONSULT Function
(BCM - AIR PRESSURE MONITOR) . . . . . ..
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) . . . . . . . ...
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
AIR PRESSURE MONITOR . . . . . . . . . ...
AIR PRESSURE MONITOR : CONSULT Function
(BCM - AIR PRESSURE MONITOR) . . . . . ..
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . ...
WITH INTELLIGENT KEY . . . . . . . . . . .
WITH INTELLIGENT KEY : List of ECU Reference
.
WITHOUT INTELLIGENT KEY . . . . . . . . ..
WITHOUT INTELLIGENT KEY : List of ECU Ref-
erence . . . . . . . . . . . . . . . . . ..
WIRING DIAGRAM . . . . . . . . . ..
TIRE PRESSURE MONITORING SYSTEM . ..
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
BCM . . . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
TIRE PRESSURE SENSOR ID REGISTRA-
TION . . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
Revision: 2013 October
2014 JUKE
WT-2
C1704, C1705, C1706, C1707 LOW TIRE
PRESSURE . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1708, C1709, C1710, C1711 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1716, C1717, C1718, C1719 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1729 VEHICLE SPEED SIGNAL . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure (With Intelligent Key Sys-
tem) . . . . . . . . . . . . . . . . . ....
Diagnosis Procedure (Without Intelligent Key Sys-
tem) . . . . . . . . . . . . . . . . . ....
POWER SUPPLY AND GROUND CIRCUIT . .
Diagnosis Procedure . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . .
TPMS . . . . . . . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
DOES NOT TURN ON . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
DOES NOT TURN OFF . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
BLINKS . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
TIRE PRESSURE SENSOR ID REGISTRA-
TION CANNOT BE COMPLETED . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . .
PERIODIC MAINTENANCE . . . . . ...
ROAD WHEEL . . . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . .
Wheel Balance Adjustment . . . . . . . . . .
Tire Rotation . . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ..
ROAD WHEEL TIRE ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
TIRE PRESSURE SENSOR . . . . . . . ..
FOR CONTINENTAL TYPE . . . . . . . . . ..
FOR CONTINENTAL TYPE : Exploded View . . .
FOR CONTINENTAL TYPE : Removal and Instal-
lation . . . . . . . . . . . . . . . . . ...
EXCEPT FOR CONTINENTAL TYPE . . . . . ...
EXCEPT FOR CONTINENTAL TYPE : Exploded
View . . . . . . . . . . . . . . . . . .
EXCEPT FOR CONTINENTAL TYPE : Removal
and Installation . . . . . . . . . . . . . .
TIRE PRESSURE RECEIVER . . . . . . ...
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Road Wheel . . . . . . . . . . . . . . .
Tire Air Pressure . . . . . . . . . . . . . .
Revision: 2013 October
2014 JUKE
PRECAUTIONS
WT-3
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009753830
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing of Battery Terminal
INFOID:0000000010291125
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Service Notice and Precautions for TPMS
INFOID:0000000009753831
• Low tire pressure warning lamp blinks for 1min, then turns ON when occurring any malfunction except low
tire pressure. Erase the self-diagnosis memories for Tire Pressure Monitoring System (TPMS), or register
the ID to turn low tire pressure warning lamp OFF. For ID registration, refer to
.
SEF289H
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст