Nissan Juke (2014 year). Service Repair Manual — part 133
DOOR OUTSIDE MOLDING
EXT-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
When installing front door outside molding, check that pawl (1)
is accurately aligned with mounting hole (2), then press in.
REAR DOOR OUTSIDE MOLDING
REAR DOOR OUTSIDE MOLDING : Removal and Installation
INFOID:0000000009750235
REMOVAL
1.
Fully open rear door glass.
2.
Twist rear door outside molding toward vehicle outside and
remove molding while disengaging it from door panel.
3.
Slide rear door outside molding (1) toward vehicle front, and
then pull molding out from rear door handle (2).
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing rear door outside molding, check that pawl (1)
is accurately aligned with mounting hole (2), then press in.
JMKIA5669ZZ
: Pawl
JMKIA5696ZZ
JMKIA5697ZZ
JMKIA5698ZZ
Revision: 2013 October
2014 JUKE
EXT-38
< REMOVAL AND INSTALLATION >
DOOR SASH TAPE
DOOR SASH TAPE
Exploded View
INFOID:0000000009750236
FRONT DOOR SASH TAPE
FRONT DOOR SASH TAPE : Removal and Installation
INFOID:0000000009750237
REMOVAL
Heat door sash tape surface using a dryer, and then peel door sash tape.
CAUTION:
Never damage painted surface of door panel.
INSTALLATION
NOTE:
For installation position of door sash tape, refer to the position as shown in the figure.
1.
Front door panel
2.
Front door sash tape
3.
Rear door sash tape
4.
Rear door panel
: Always replace after every disassembly.
JMKIA5665ZZ
Revision: 2013 October
2014 JUKE
DOOR SASH TAPE
EXT-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
CAUTION:
• Degrease door panel mounting surface for sash tape.
• Paint grain or dust on mounting surface of sash tape may spoil exterior appearance if it remains.
Clean the mounting surface and check that no paint grain or dust remains, before starting the opera-
tion.
• Never reuse blackout tape.
1.
Affix door sash tape align blackout tape upper portion to rear door outer upper end.
2.
Affix door sash tape (2) to door panel (3) by applying pressure using a squeegee (A) while peeling offre-
lease coated paper (1).
NOTE:
• Peel release coated paper at distance of 10 – 20 mm (0.394 – 0.787 in) ahead (B) of squeegee and affix
blackout paper.
• To prevent any bubbles from forming, slightly lift the portion, not yet affixed using squeegee, so that por-
tion dose not contact with panel surface. Apply pressure and affix at a low and constant speed using
squeegee tilted at 40 – 50
°
angle (pushing direction) (C) 30 – 45
°
angle (pulling direction) (D).
1.
Front door panel
2.
Front door sash tape
3.
Rear door panel
R.
Radius
: Always replace after every disassembly.
D
: 2.0 mm (0.08 in)
E
: 4.0 mm (0.16 in)
JMKIA5666ZZ
Revision: 2013 October
2014 JUKE
EXT-40
< REMOVAL AND INSTALLATION >
DOOR SASH TAPE
3.
For small radius portion of hemming part, gradually apply pres-
sure and affix door sash tape (1) using squeegee (A) in 1 – 3
steps.
CAUTION:
Never wash the vehicle with in 24 hours so as to keep adhe-
sive.
REAR DOOR SASH TAPE
REAR DOOR SASH TAPE : Removal and Installation
INFOID:0000000009750238
REMOVAL
Heat door sash tape surface using a dryer, and then peel door sash tape.
CAUTION:
Never damage painted surface of door panel.
INSTALLATION
NOTE:
For installation position of door sash tape, refer to the position as shown in the figure.
JMKIA4862GB
JMKIA4655ZZ
Revision: 2013 October
2014 JUKE
DOOR SASH TAPE
EXT-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
CAUTION:
• Degrease door panel mounting surface for door sash tape.
• Paint grain or dust on mounting surface of door sash tape may spoil exterior appearance if it
remains. Clean the mounting surface and check that no paint grain or dust remains, before starting
the operation.
• Never reuse door sash tape.
1.
Affix door sash tape align door sash tape upper portion to rear door outer upper end.
2.
Affix door sash tape (2) to door panel (3) by applying pressure using a squeegee (A) while peeling off
release coated paper (1).
NOTE:
• Peel release coated paper at distance of 10 – 20 mm (0.394 – 0.787 in) ahead (B) of squeegee and affix
blackout paper.
• To prevent any bubbles from forming, slightly lift the portion, not yet affixed using squeegee, so that por-
tion dose not contact with panel surface. Apply pressure and affix at a low and constant speed using
squeegee tilted at 40 – 50
°
angle (pushing direction) (C) 30 – 45
°
angle (pulling direction) (D).
1.
Rear door panel
2.
Rear door sash tape
3.
Front door panel
R.
Radius
: Always replace after every disassembly.
D
: 2.0 mm (0.08 in)
JMKIA5667ZZ
Revision: 2013 October
2014 JUKE
EXT-42
< REMOVAL AND INSTALLATION >
DOOR SASH TAPE
3.
For small radius portion of hemming part, gradually apply pres-
sure and affix door sash tape (1) using squeegee (A) in 1 – 3
steps.
CAUTION:
Never wash the vehicle with in 24 hours so as to keep adhe-
sive.
JMKIA4862GB
JMKIA4655ZZ
Revision: 2013 October
2014 JUKE
REAR FENDER COVER
EXT-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REAR FENDER COVER
Exploded View
INFOID:0000000009750239
Removal and Installation
INFOID:0000000009750240
REMOVAL
Disengage rear fender cover fixing clips using remover tool (A), and
then remove rear fender cover.
CAUTION:
Apply protective tape (B) to the body side to protect from dam-
age.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing rear fender cover, check that clips are securely fitted in body panel holes, and then
press them it.
JMKIA5663ZZ
1.
Rear fender cover
2.
Rear fender
: Clip
JMKIA5668ZZ
Revision: 2013 October
2014 JUKE
EXT-44
< REMOVAL AND INSTALLATION >
BACK DOOR FINISHER
BACK DOOR FINISHER
Exploded View
INFOID:0000000009750241
Removal and Installation
INFOID:0000000009750242
REMOVAL
1.
Remove back door trim. Refer to
INT-39, "BACK DOOR LOWER FINISHER : Removal and Installation"
2.
Remove back door finisher mounting nuts.
3.
Disconnect license lamp, back door opener request switch and rear view camera harness connectors.
4.
Remove harness grommet.
5.
Disengage back door finisher fixing clips using a remover tool
(A), and then remove back door finisher.
6.
Disengage fixing clips at both ends of back door finisher from
inside of back door.
CAUTION:
• Apply protect tape (B) on back door panel to protect the
painted surface from damage.
• Never pull back door finisher strongly.
INSTALLATION
1.
Rear view camera
2.
Back door opener request switch
3.
Emblem
4.
Back door finisher
: Clip
: Pawl
: Always replace after every disassembly.
JMKIA5733ZZ
: Clip
JMKIA6179ZZ
Revision: 2013 October
2014 JUKE
BACK DOOR FINISHER
EXT-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing back door finisher, check that clip are securely in body panel holes, and press them in.
Revision: 2013 October
2014 JUKE
EXT-46
< REMOVAL AND INSTALLATION >
REAR SPOILER
REAR SPOILER
Exploded View
INFOID:0000000009750243
JUKE NISMO
Removal and Installation
INFOID:0000000009750244
REMOVAL
1.
Remove fixing grommet.
2.
Remove rear spoiler mounting nuts.
3.
Cut rear spoiler fixing double-sided tape.
4.
Remove rear spoiler fixing clips.
5.
Disconnect high-mounted stop lamp harness connector, and then remove rear spoiler.
6.
Remove the following parts after removing rear spoiler:
• High-mounted stop lamp cover.
• High-mounted stop lamp. Refer to
.
INSTALLATION
JSKIA3180GB
1.
Rear spoiler
2.
High-mounted stop lamp
3.
High-mounted stop lamp cover
4.
Double-sided tape
[t: 2.0 mm (0.079 in)]
5.
Double-sided tape
[t: 1.2 mm (0.047 in)]
: Clip
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Indicates that the part is connected at points with same symbol in actual vehicle.
Revision: 2013 October
2014 JUKE
REAR SPOILER
EXT-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never damage the back door assembly.
• Replace the double-sided tape on the back surface with new double-sided tape when reusing the
rear spoiler.
• Remove double-sided tape remaining on back door assembly and back of rear spoiler with a double-
sided tape remover, after removing rear spoiler.
• When installing, visually check the rear spoiler and clips, then replace them with new parts if they
are damaged.
• When installing rear spoiler, check clips and bolts are securely in back door assembly holes, and
press them in.
• Never wash the vehicle within 24 hours after installing so as to keep adhesive.
Revision: 2013 October
2014 JUKE
FAX-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
FAX
A
B
FAX
N
O
P
CONTENTS
FRONT AXLE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Drive Shaft . . . . . . . . . ...
Precautions for Removing of Battery Terminal . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
FRONT WHEEL HUB AND KNUCKLE . . . ..
Inspection . . . . . . . . . . . . . . . . ..
FRONT DRIVE SHAFT . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
FRONT WHEEL HUB AND KNUCKLE . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . .
FRONT DRIVE SHAFT BOOT . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Removal and Installation . . . .
TRANSAXLE SIDE . . . . . . . . . . . . .
TRANSAXLE SIDE : Removal and Installation . ...
Inspection . . . . . . . . . . . . . . . .
FRONT DRIVE SHAFT . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
LEFT SIDE . . . . . . . . . . . . . . . . .
LEFT SIDE : Removal and Installation . . . . .
RIGHT SIDE . . . . . . . . . . . . . . . ...
RIGHT SIDE : Removal and Installation . . . . ..
WHEEL SIDE . . . . . . . . . . . . . . . .
WHEEL SIDE : Disassembly and Assembly . . ...
TRANSAXLE SIDE . . . . . . . . . . . . .
TRANSAXLE SIDE : Disassembly and Assembly
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Bearing . . . . . . . . . . . . . . .
Drive Shaft . . . . . . . . . . . . . . . ...
Revision: 2013 October
2014 JUKE
FAX-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009750065
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Drive Shaft
INFOID:0000000009750066
• Observe the following precautions when disassembling and assembling drive shaft.
- Never disassemble joint sub-assembly because it is non-overhaul parts.
- Perform work in a location which is as dust-free as possible.
- Clean the parts, before disassembling and assembling.
- Prevent the entry of foreign objects during disassembly of the service location.
- Reassemble disassembled parts carefully in the correct order. If work is interrupted, a clean cover must be
placed over parts.
- Use paper waste. Fabric shop cloths must not be used because of the danger of lint adhering to parts.
- Clean disassembled parts (except for rubber parts) with kerosene which shall be removed by blowing with
air or wiping with paper waste.
Revision: 2013 October
2014 JUKE
PRECAUTIONS
FAX-3
< PRECAUTION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Precautions for Removing of Battery Terminal
INFOID:0000000010181605
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
Revision: 2013 October
2014 JUKE
FAX-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009750067
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-More No.)
Tool name
Description
KV40104000
(
—
)
Hub lock nut wrench
a: 85 mm (3.35 in)
b: 65 mm (2.56 in)
Removing and Installing wheel hub lock nut.
KV40107300
(
—
)
Boot band crimping tool
Installing boot band
KV40107500
(
—
)
Drive shaft attachment
Removing drive shaft
KV38107900
(
—
)
Protector
a: 32 mm (1.26 in) dia.
Installing drive shaft
ZZA0802D
ZZA1229D
ZZA1230D
PDIA1183J
Revision: 2013 October
2014 JUKE
PREPARATION
FAX-5
< PREPARATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Commercial Service Tools
INFOID:0000000009750068
Tool name
Description
Power tool
Loosening bolts and nuts
Drive shaft puller
Removing drive shaft joint sub assembly
Sliding hammer
Removing drive shaft
Ball joint remover
Removing hub bolt
PBIC0190E
JPDIG0152ZZ
ZZA0023D
NT146
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст